Replacement Parts Q&A

Question 1

do you make a similar cap for the RJ+ (RJ60N) ? View answer

Asked 6 ´years ago

Question 2

Chlorine is not being generated. New cell with about 6 months service. Will a problem with the small board not indexing causing this problem? View answer

Asked 4 ´years ago

Question 3

My flow sensor has failed! Now can I replace just the flow sensor w/out cutting any PVC pipe? View answer

Asked 3 ´years ago | CircuPool® Flow Switch / Temperature Sensor (No PVC Tee Fitting)

Question 4

Will this fit the sj as well cause I can’t find this part for the sj?? View answer

Asked 3 ´years ago | Replacement Parts > Parts & Accessories > RJ-PLUS Models > CircuPool® Threaded Cell Collar - RJ (3rd-Generation)

Question 5

Is the circuit board for a CircuPool Universal Series??? View answer

Asked 4 ´years ago

Question 6

Is this compatible with the CORE 35? View answer

Asked 9 ´months ago | Replacement Parts > Parts & Accessories > SJ-A Models

Question 7

Is this for the core control model? View answer

Asked 9 ´months ago

Question 8

RJ PLUS display locked in cell connection. View answer

Asked 9 ´months ago | Replacement Parts > Parts & Accessories > RJ-PLUS Models

Question 9

is it the head of the core 55 right? View answer

Asked 9 ´months ago

Question 10

I have an RJ 30 and need replacement "O" rings one for each end. Not sure the 3 you show fit my unit (purchased 2/2016). Please advise. Part number and cost. View answer

Asked 5 ´years ago

Question 11

Is this the main board for the chlorine generator. View answer

Asked 4 ´years ago

Question 12

Is the CircuPool® Replacement Union sold as a single piece or as a pair? View answer

Asked 4 ´years ago

Question 13

Does this fit RJ30? Also, where is it located and how do you remove old one? View answer

Asked 4 ´years ago

Question 14

I am reinstalling my RJ60+ because of leaks. Is this union the same as the one that came with my RJ60+. Does it a a groove cut in it for the o-ring? View answer

Asked 3 ´years ago

Question 15

Sediment chamber replacement View answer

Asked 7 ´months ago | Replacement Parts > Pump / Filter Models

Question 16

does this come as one or both pieces View answer

Asked 5 ´years ago

Question 17

Looking for replacement unions and O-rings for RJ-45+ What is the part number? View answer

Asked 5 ´years ago

Question 18

I have the RJ 45 the clear housing is fine but the clear some that covers the wired is cracked can I replace that p View answer

Asked 6 ´months ago | Replacement Parts > Parts & Accessories > RJ-Classic Models

Question 19

Can I get replacement control module? View answer

Asked 5 ´months ago | Replacement Parts > Parts & Accessories > EDGE Models

Question 20

Do you offer the full cover (blue part)? Roofers damaged mine and would like to replace it. View answer

Asked 4 ´months ago

Question 21

I have an RJ 60 my unit says no flow. I've put a new flow switch still says it View answer

Asked 19 ´days ago

Question 22

Hello, the Replacement Union looks like the part I need but I'm unsure. I do have a classic RJ system. The part I need fills the open end of the clear cylinder. It also hold the electrodes. I also need the bolts and male electrodes, and the rubber o ring. I would also like to buy a replacement electrical cord with the female red, black, and blue connectors attached. Could you please supply part number so I can order?Thank you, Rih Kosina View answer

Asked 6 ´years ago

Question 23

Is there a replacement cable for the RJ series which connects the controller to the cell? I believe my blue connector has failed. View answer

Asked 7 ´years ago

Question 24

Is the screen replaceable? I did not see in on the site. View answer

Asked 4 ´years ago

Question 25

where can buy the maie end of a cicircopool salt generator View answer

Asked 4 ´years ago

Question 26

The valve on the bypass seems counterintuitive. When in bypass, a small amount of DE goes into the cyclone.

Asked 1 ´month ago

Question 27

You only show one end of the cord. Does the other end have the threaded part that screws into the RJ-45 unit? View answer

Asked 6 ´years ago

Question 28

can i get an o ring for my cleaning stand View answer

Asked 28 ´days ago

Question 29

How do u replace a fuse on the RJ30 CircuPool salt system. Icant see how u open case. System comes on then turns off and light % dims on and off. View answer

Asked 4 ´years ago

Question 30

The keypad is showing output-off when I reset by pressing the + key and bring it up to 60 or 80, but in a few minutes or couple hours is back on output-off, Do I need a new keypad or a new circuit board? thank you View answer

Asked 5 ´years ago

Question 31

My keypad no longer is working. Nothing is displayed. How do I replace it? View answer

Asked 6 ´years ago

Question 32

Do this part fits on a power module serial 130273? View answer

Asked 7 ´years ago

Question 33

what is the small electrical black plug terminal used for it came in the bag with the screws and o rings

Asked 1 ´month ago | Replacement Parts > Parts & Accessories > SJ-A Models

Question 34

Is a cleaning cap for the rj plus series same as winter cap I hope not View answer

Asked 2 ´years ago | Replacement Parts > Parts & Accessories > RJ-PLUS Models

Question 35

Does it come with the o -ring View answer

Asked 2 ´years ago

Question 36

Suction View answer

Asked 2 ´years ago

Question 37

why do i continue to have a negative volt reading View answer

Asked 2 ´years ago | Replacement Parts > Parts & Accessories > Si / Universal Models

Question 38

Are there any directions on how to use the CircuPool® SJ-Series Cleaning Tool? View answer

Asked 2 ´years ago

Question 39

We have the Rj 30 salt cell the keypad is no longer letting me change the settings. View answer

Asked 2 ´years ago | Replacement Parts > Parts & Accessories > RJ-Classic Models

Question 40

On TJ-16 with stand, what is the height from ground to top of outlet fitting? View answer

Asked 3 ´years ago

Question 41

can these pumps be used on 1 1/2" plumbing? View answer

Asked 3 ´years ago

Question 42

I have installed the SWG vertically. When running, the SWG isn't completely full of water. Is that OK? View answer

Asked 3 ´years ago | Replacement Parts > Parts & Accessories > Brand Adapter Kits > CircuPool® Vertical Installation Kit

Question 43

I HAVE DISCONNECTED MY UNIVERSAL SERIES FOR THE WINTER BUT MY FLOW SWITCH IS STILL IN MY FUNCTIONING SYSTEM CAN THE SENSOR BE UNSCREWED FROM TOP OF TEE/SWITCH BE TAKEN OUT AND PLUGGED WITH NO PROBLEM View answer

Asked 5 ´years ago | CircuPool® Flow Switch Housing

Question 44

Would this work for a 1.5 HP pump? I've blown 2 timers in two years because they couldn't handle the load of the pump and salt system. View answer

Asked 3 ´years ago

Question 45

Are these the O-rings needed to fit the replacement union? View answer

Asked 4 ´years ago | CircuPool® O-Ring Set for RJN/UL/Si

Question 46

I have a core 35 and need a bypass for winter. Does this work? What is the measured length? If it’s longer, no problem I can cut down. Thanks View answer

Asked 4 ´years ago | CircuPool® Bypass Cell for RJ-PLUS and UL-Series Salt Systems

Question 47

I have a UL40 system, will this fit? View answer

Asked 5 ´years ago | CircuPool® Bypass Cell for RJ-PLUS and UL-Series Salt Systems

Question 48

I have received two of these cells from a CircuPool dealer and both of them will not thread onto my CircuPool RJ60+ union collars. They will thread onto the cleaning stand. Has CircuPool changed the suppliers recently, or changed the threads on one or the other? View answer

Asked 5 ´years ago | CircuPool® Bypass Cell for RJ-PLUS and UL-Series Salt Systems

Question 49

The Universal UL40 unit sent from factory set to accept 220/240v. Do I need two lugs to accept 110/120V ? View answer

Asked 1 ´year ago

Question 50

will this stand work for RJ 30N model View answer

Asked 3 ´years ago | CircuPool® Cleaning Stand for CircuPool RJ Plus, Universal, and Si Systems

Replacement Parts Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic

Tools