Parts & Accessories Q&A

Question 1

My RJ45 temperature displays high at 168.9 degree but my water temperature is only 57 degrees View answer

Asked 1 ´year ago

Question 2

Is the flow switch required on a salt chlorinator system? View answer

Asked 3 ´years ago

Question 3

This setup comes with the unions to connect to cell? View answer

Asked 10 ´months ago

Question 4

flow switch not working View answer

Asked 3 ´years ago

Question 5

Do this part fits on a power module serial 130273? View answer

Asked 6 ´years ago

Question 6

I need some O rings for this CircuPool CORE35 Salt Chlorine Generator. How can I order them? View answer

Asked 1 ´year ago

Question 7

What is the water flow direction thru the cell View answer

Asked 5 ´years ago

Question 8

Will the CircuPool SmartFlo Interface Kit work on a new inground Black & Decker VS pump? View answer

Asked 2 ´years ago

Question 9

I have the RJ45+ saltwater chlorinator. I need 2 replacement unions for 1-1/2 piping.

Asked 2 ´years ago

Question 10

Will this work with the TJ-16 Typhoon prefilter? It has 2 " fittings and my plumbing is 1 1/2". View answer

Asked 10 ´months ago

Question 11

Can I use this to bypass my CORE55 for the winter? Are the threads compatible? I would most likely need to shorten it to fit. I would rather remove the whole unit for the winter than using the cap for the unit and leaving the clear housing that may crack from freezing View answer

Asked 5 ´years ago | CircuPool® Bypass Cell for RJ-PLUS and UL-Series Salt Systems

Question 12

Will this bypass cell fit a Circupool Core 35 salt generator? View answer

Asked 6 ´years ago | CircuPool® Bypass Cell for RJ-PLUS and UL-Series Salt Systems

Question 13

I have a si45 plus and my system is set up F15, my pool is 4o,ooo gal, what cell is the best and longest warranty View answer

Asked 11 ´months ago | Support

Question 14

How do I know which the flow switch is the right with temp senor or without? the both say they are for RJ+ series View answer

Asked 10 ´months ago

Question 15

Can I use any flow switch from local pool place? View answer

Asked 8 ´months ago

Question 16

I have RJ60+ and have high temp reading which is incorrect. View answer

Asked 1 ´year ago

Question 17

Is this product compatible with the Circupool Si 55 Universal salt cell? View answer

Asked 1 ´year ago

Question 18

CircuPool RJ+ PCB Adapter Installation Instructions. View answer

Asked 2 ´years ago | Replacement Parts > Parts & Accessories

Question 19

Which direction is flow?? View answer

Asked 5 ´years ago

Question 20

i HAVE AN rj45+ AND MORE TIMES THEN NOT i CANT GET THE POWER TO TURN ON OR OFF. dO i NEED A NEW KEYPAD? View answer

Asked 2 ´years ago

Question 21

My system is currently plumed for a Pentair 520555 IntelliChlor IC40. would this adapter kit work? Also would the i be able to mount the salt generator vertically instead of horizontally? Thanks, Gary . View answer

Asked 4 ´years ago

Question 22

I am needing a replacement fitting for a rj45 salt cell. The pvc fitting broke loose from the 2” pipe. View answer

Asked 3 ´years ago | Replacement Parts > Parts & Accessories > RJ-PLUS Models > CircuPool® Replacement Union - RJ-N (3rd Gen.) Models

Question 23

I HAVE DISCONNECTED MY UNIVERSAL SERIES FOR THE WINTER BUT MY FLOW SWITCH IS STILL IN MY FUNCTIONING SYSTEM CAN THE SENSOR BE UNSCREWED FROM TOP OF TEE/SWITCH BE TAKEN OUT AND PLUGGED WITH NO PROBLEM View answer

Asked 5 ´years ago | CircuPool® Flow Switch Housing

Question 24

Is this the Part that the ORing fits into? View answer

Asked 4 ´years ago

Question 25

Does this stand work for the RJ45+ series cells?? Not very clear from the description. Thanks, Mike View answer

Asked 4 ´years ago | CircuPool® Cleaning Stand for CircuPool RJ Plus, Universal, and Si Systems

Question 26

Will part number CORE-CLHS fit a CORE 35? View answer

Asked 3 ´years ago

Question 27

Flow sensor warranty? View answer

Asked 1 ´year ago

Question 28

How much space do you need for a vertical install in length View answer

Asked 9 ´months ago

Question 29

I am reinstalling my RJ60+ because of leaks. Is this union the same as the one that came with my RJ60+. Does it a a groove cut in it for the o-ring? View answer

Asked 3 ´years ago

Question 30

Is there any issue installing in a vertical configuration with a variable speed pump on a low setting? View answer

Asked 2 ´years ago

Question 31

Will this replace the rj45 View answer

Asked 3 ´years ago

Question 32

I have a core 35 and need a bypass for winter. Does this work? What is the measured length? If it’s longer, no problem I can cut down. Thanks View answer

Asked 4 ´years ago | CircuPool® Bypass Cell for RJ-PLUS and UL-Series Salt Systems

Question 33

Do these caps fit on the union ends of the cell body? View answer

Asked 1 ´month ago

Question 34

The Flow LED on the panel will turn green for aprox. 10 seconds and then go red for aprox. 2 min. When it will go green again for 10 seconds repeating. Could this be a faulty flow switch or something else? View answer

Asked 3 ´years ago

Question 35

How much pipe do I need to cut from the plumbing to install a new RJ30+ flow switch? View answer

Asked 1 ´year ago

Question 36

My RJ30+ was professionally installed, three weeks ago. It appears it is running. BUT it is not generating chlorine. View answer

Asked 1 ´year ago

Question 37

Is there a good way to clean the core 35 cell. View answer

Asked 12 ´months ago

Question 38

Does this fit RJ30? Also, where is it located and how do you remove old one? View answer

Asked 4 ´years ago

Question 39

Will this keypad fit my rj30 ? View answer

Asked 3 ´years ago

Question 40

Is this the correct 2" cell union for a RJ30+ system? View answer

Asked 5 ´years ago

Question 41

Will this fit the sj as well cause I can’t find this part for the sj?? View answer

Asked 3 ´years ago | Replacement Parts > Parts & Accessories > RJ-PLUS Models > CircuPool® Threaded Cell Collar - RJ (3rd-Generation)

Question 42

Should I clean the salt cell before I put it away for the winter? View answer

Asked 1 ´year ago

Question 43

Why not sell the flow switch with the Tee? But you you show the sensor with the tee to sell the sensor. View answer

Asked 2 ´years ago

Question 44

will the cleaning stand nut replace a cracked one on my salt cell? CIRCUPOOL® CLEANING STAND FOR CIRCUPOOL RJ, UNIVERSAL, AND SI SYSTEM can the nut with this replace a cracked nut on me cell housing? View answer

Asked 5 ´years ago | CircuPool® Cleaning Stand for CircuPool RJ Plus, Universal, and Si Systems

Question 45

Is this female to female View answer

Asked 2 ´years ago | Replacement Parts > Parts & Accessories > CORE Models > CircuPool CORE 2-in Union Set (Unions plus Collars)

Question 46

I love my salt chlorine generator but I use a lot of acid for the pH. Is this caused by it generating chlorine? View answer

Asked 2 ´years ago

Question 47

What is the diameter of the threaded pipe this connects to? View answer

Asked 5 ´years ago | CircuPool® Cleaning Stand for CircuPool RJ Plus, Universal, and Si Systems

Question 48

My keypad no longer is working. Nothing is displayed. How do I replace it? View answer

Asked 6 ´years ago

Question 49

I have a RJ 45 and am getting a high temp warning even though the water isn't hot at all. It is preventing the unit

Asked 1 ´year ago

Question 50

How can I tell what unit I have, SJ-20...SJ-35...SJ-45??? View answer

Asked 1 ´year ago

Parts & Accessories Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic

Tools