Replacement Parts Q&A

Question 1

does it fit for sj40 series? View answer

Asked 3 ´years ago

Question 2

Is this the ORing that goes in the Union Nut to seal against the Face of the Generator? View answer

Asked 3 ´years ago

Question 3

what does the other side look like? Could you send a picture of the top side of the unit as it would appear on the pump? Does it have the clock display and programming buttons that is removed when attaching this to the motor? View answer

Asked 3 ´years ago

Question 4

my old cell housing is leaking so i need to replace it. i ordered a new one which has treaded connectors but the existing housing was glued to the PVC . What parts do I need to connect the new housing unit? I have a SJ View answer

Asked 3 ´years ago

Question 5

does the vertical install work with a variable speed pump, low speed View answer

Asked 3 ´years ago

Question 6

How do u replace a fuse on the RJ30 CircuPool salt system. Icant see how u open case. System comes on then turns off and light % dims on and off. View answer

Asked 3 ´years ago

Question 7

Is this the main board for the chlorine generator. View answer

Asked 3 ´years ago

Question 8

Do you sell just the 2 white parts for the core55? I wasn't paying attention when installing and ended up installing the cell before my heater. Now, I need to relocate it downstream. I don't need the gray pieces as mine are still good as the unit is new. View answer

Asked 3 ´years ago

Question 9

Will this fit model S160? Serial no 05aa5da3f50037 View answer

Asked 3 ´years ago

Question 10

Would this flow meter work in a 305 px natural chlorine generator? It looks exactly the same as the one I'm replacing. View answer

Asked 3 ´years ago

Question 11

Is the CircuPool® Replacement Union sold as a single piece or as a pair? View answer

Asked 3 ´years ago

Question 12

Does the CircuPool Cleaning Stand for RJ also fit RJ+ View answer

Asked 3 ´years ago | CircuPool® Cleaning Stand for CircuPool RJ Plus, Universal, and Si Systems

Question 13

I have a core 35 and need a bypass for winter. Does this work? What is the measured length? If it’s longer, no problem I can cut down. Thanks View answer

Asked 3 ´years ago | CircuPool® Bypass Cell for RJ-PLUS and UL-Series Salt Systems

Question 14

Hi can you install the Circu pool vertical installation with the pvc pipe openings towards the top , with the cell on the left ( looking at item)? View answer

Asked 3 ´years ago

Question 15

This unions fits on circupool 35 and 55 core ?? View answer

Asked 3 ´years ago

Question 16

where is reset button located on rj 45? My serial number is 030255 View answer

Asked 3 ´years ago

Question 17

Which replacement cartridge will this need? View answer

Asked 3 ´years ago

Question 18

I have a rj 45 classic the it had on panel.power off and will not turn on will the key pad help this or do u need a whole new control panel View answer

Asked 3 ´years ago

Question 19

I need two o rings for my salt cell connection RJ 45 View answer

Asked 3 ´years ago

Question 20

Will this kit work OK when connected to 1 1/2 inc h PVC? View answer

Asked 4 ´years ago

Question 21

Does this item come with an o-ring? View answer

Asked 4 ´years ago

Question 22

What’s are the measurements of this filter? View answer

Asked 4 ´years ago

Question 23

Is there something like that for RJ classic? View answer

Asked 4 ´years ago

Question 24

I have a UL40 system, will this fit? View answer

Asked 4 ´years ago | CircuPool® Bypass Cell for RJ-PLUS and UL-Series Salt Systems

Question 25

My system is currently plumed for a Pentair 520555 IntelliChlor IC40. would this adapter kit work? Also would the i be able to mount the salt generator vertically instead of horizontally? Thanks, Gary . View answer

Asked 4 ´years ago

Question 26

I have an RJ 30 and need replacement "O" rings one for each end. Not sure the 3 you show fit my unit (purchased 2/2016). Please advise. Part number and cost. View answer

Asked 4 ´years ago

Question 27

What are the specific sizes of each of the 3 O rings? Where does each of the 3 O rings go? What are the instructions for replacing an O rings? Are any other parts needed? View answer

Asked 4 ´years ago

Question 28

does this come as one or both pieces View answer

Asked 4 ´years ago

Question 29

Looking for replacement unions and O-rings for RJ-45+ What is the part number? View answer

Asked 4 ´years ago

Question 30

Is this the correct 2" cell union for a RJ30+ system? View answer

Asked 4 ´years ago

Question 31

I have limited amount of space for a vertical installation. What is the height needed for a vertical install? If the unit cannot fit vertically, can it be installed horizontally using this vertical install kit? Thank you. View answer

Asked 4 ´years ago

Question 32

Which direction is flow?? View answer

Asked 4 ´years ago

Question 33

What is the diameter of the threaded pipe this connects to? View answer

Asked 4 ´years ago | CircuPool® Cleaning Stand for CircuPool RJ Plus, Universal, and Si Systems

Question 34

Does the Bypass Cell for the RJ45 comes with O-rings at each end? View answer

Asked 4 ´years ago | CircuPool® Bypass Cell for RJ-PLUS and UL-Series Salt Systems

Question 35

Cutting the cord is okay when replacing the collar cap. Or is there a way to disassemble the plug? View answer

Asked 4 ´years ago

Question 36

I HAVE DISCONNECTED MY UNIVERSAL SERIES FOR THE WINTER BUT MY FLOW SWITCH IS STILL IN MY FUNCTIONING SYSTEM CAN THE SENSOR BE UNSCREWED FROM TOP OF TEE/SWITCH BE TAKEN OUT AND PLUGGED WITH NO PROBLEM View answer

Asked 4 ´years ago | CircuPool® Flow Switch Housing

Question 37

will this fit the sj-15 salt cell . The one that holds the cell .with the cord to the clear plastic housing. my blue collar has a crack in it View answer

Asked 4 ´years ago

Question 38

Is there a 3 inch version? All my plumbing is 3 and 3 in. View answer

Asked 4 ´years ago

Question 39

Can I use this to bypass my CORE55 for the winter? Are the threads compatible? I would most likely need to shorten it to fit. I would rather remove the whole unit for the winter than using the cap for the unit and leaving the clear housing that may crack from freezing View answer

Asked 4 ´years ago | CircuPool® Bypass Cell for RJ-PLUS and UL-Series Salt Systems

Question 40

Which terminal on the circuit board does the blue wire connect too ? Foolish me forgot to mark it when removing. View answer

Asked 4 ´years ago

Question 41

What is the water flow direction thru the cell View answer

Asked 4 ´years ago

Question 42

Is this the right 2" union for a RJ +? View answer

Asked 4 ´years ago

Question 43

Does this o ring fit the 2" union? View answer

Asked 4 ´years ago

Question 44

I am considering the Core55 replacing an a pure 1400 salt cell. Will this adapter work to replace the salt cell? View answer

Asked 4 ´years ago

Question 45

I read somewhere that I would need to get a core model for twice the size of my pool. I have a 22k gallon pool so with that logic I would need a core55. Also is there anything else I need to hardwire into my existing timer or should I get a new timer? View answer

Asked 4 ´years ago

Question 46

I have received two of these cells from a CircuPool dealer and both of them will not thread onto my CircuPool RJ60+ union collars. They will thread onto the cleaning stand. Has CircuPool changed the suppliers recently, or changed the threads on one or the other? View answer

Asked 4 ´years ago | CircuPool® Bypass Cell for RJ-PLUS and UL-Series Salt Systems

Question 47

will the cleaning stand nut replace a cracked one on my salt cell? CIRCUPOOL® CLEANING STAND FOR CIRCUPOOL RJ, UNIVERSAL, AND SI SYSTEM can the nut with this replace a cracked nut on me cell housing? View answer

Asked 4 ´years ago | CircuPool® Cleaning Stand for CircuPool RJ Plus, Universal, and Si Systems

Question 48

Can the convertor cell be mounted vertically and the flow detector be mounted on the adjacent horizontal run ? What horizontal straight tube length should precede the flow device along the horizontal tube run ? View answer

Asked 4 ´years ago

Question 49

The keypad is showing output-off when I reset by pressing the + key and bring it up to 60 or 80, but in a few minutes or couple hours is back on output-off, Do I need a new keypad or a new circuit board? thank you View answer

Asked 4 ´years ago

Question 50

Do I need this and how does it work.? is it connected to any thing like water or just a stand? View answer

Asked 4 ´years ago | CircuPool® Cleaning Stand for CircuPool RJ Plus, Universal, and Si Systems

Replacement Parts Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic

Tools