CircuPool® Classic Combo (Salt Chlorinator + Pump) Q&A
Activity timeframe
This says it can produce up to 1.4 lbs of chlorine per day. Would this be assuming it is running at 100% output for 24 hours? Just trying to figure out my run time and output settings. Last year I was using about a 1/2 pound to 3/4 pound of chlorine per day before I installed this salt cell View answer
Asked 4 ´years ago
How do I shock my salt water pool that has a RJ60+ system. View answer
Asked 2 ´years ago
Does the CORE55 control need to be protected from sunlight? View answer
Asked 4 ´years ago
What’s the average lifespan of the cell in the RJ30? View answer
Asked 3 ´years ago
What is the current draw of the entire system if running on 110VAC? View answer
Asked 4 ´years ago
I have a 10,000 gallon pool and want to convert to salt. So many questions. It's been 3 years since I drained and replaced 1/2 the water in the pool due to a repair. Should I consider a water replacement prior to conversion ? Under what circumstances should I consider water replacement? Money not an option...which model should I buy? What size? When does increase size not benefit performance for salt conversion power, cell cleaning cycle time, and cell life? Installation should not be a consideration as all would fit my system. Thank you, Bill View answer
Asked 3 ´years ago
Hello, What is the minimum flow rate (GPM) for operation for the CircuPool Core series? I currently have a Jandy VSP pump that I run at 1200 rpms that generates 22 gpm. Would the Chlorinator work at this low flow rate? Thanks in advance for your assistance. Have a GREAT Day. Regards, Eric Brown View answer
Asked 3 ´years ago
I have a variable speed pump. The question is, when I am at the low speed I suspect the flow will not be enough for the flow switch to read so it will not produce salt. Is this correct? Will this harm the system?If I purchase this my plan is to set the pump speeds to get the chlorine level I need. Pool is 15000 gallons View answer
Asked 3 ´years ago
Is this compatible for a compupool inlet and outlet hook ups? View answer
Asked 6 ´years ago
I bought a house with a 26qft pool. I'm trying to learn to control the salt chlorinator (SJ series) for my pool. The water is murky now, with algae. All parameters are ok (I check regularly), except chlorine and free chlorine levels, which are at 0. How do I know that the cell actually works? Is there a documentation regarding the controller? the left bottom green light has been blinking. Also, how is this controller related to the pump? I have Hayward controller for the pump, and I'm clueless here too. Please help. View answer
Asked 3 ´years ago
what size pipe is used for the inlet and outlet and is it PVC? View answer
Asked 3 ´years ago
Will this be a direct replacement for the Si45? View answer
Asked 4 ´years ago
I have a SJ-series system 4 years ago. works great. I just had a variable speed pool pump installed. It goes threw its own internal timers. does the SJ- series have a built in flow switch sensor built in. Worried about the unit coming on via the old pool timer without the new pump running? View answer
Asked 5 ´years ago
What is the minimum GPM flow rate required for the Core series? View answer
Asked 4 ´years ago
Does this unit come with a plug for 120 vac or is it hard wired? View answer
Asked 3 ´years ago
water pump qualifies for energy star tax credit View answer
Asked 3 ´years ago
can this unit be powered up 24/7, or does it need a timer/clock? View answer
Asked 4 ´years ago
is this unit 220V or 115V View answer
Asked 3 ´years ago
How can I get a pdf of the manual View answer
Asked 4 ´years ago
How do I buy a replacement for the SJ 3500 Generator buy it's self?? View answer
Asked 3 ´years ago
How can I tell what my salinity level is on the Core35 unit? View answer
Asked 4 ´years ago
I have an inground 11,500gal (estimate) pool. I have a 100 sq ft cartridge filter. All visible plumbing is 1-1/2" PVC. The current pump motor is 1 HP single speed. I would like to upgrade to a VS pump to run 8 hrs per day and turn the pool over 2x/day. I'm also considering the RJ-20PLUS SWCG. What size motor should I use - the 1.5, 2.0 or the 3.0HP??? Also, do you agree with the RJ-20 or should I go with the RJ-30? View answer
Asked 3 ´years ago
We just cleaned our cell and now we are having issues with it communicating to the system. There is a code saying Cell Connection. We have inspected the all of the cables and everything look to be in good shape. We have powered it down several times and disconnected it several times as well yet we can not get the cell to communicate with the system, W”hat could be the cause of this code? View answer
Asked 4 ´years ago
I have the Edge40. After a big rainstorm, the system told me that salt level was low. I added a few bags, and got it tested. Showings 4500 level. I had it running on high and boost for about 6 hours, yet my chlorine levels were still extremely low. I then cleaned the cell by the book and ran it again for a few hours with no change to chlorine levels. Still shows no chlorine when tested. I looked at the cell with a flashlight while it was running. I did see the electrolysis bubbles being formed. Yet after a few hours the chlorine levels did not rise. Please advise. View answer
Asked 4 ´years ago