Sanitation Q&A

Question 1

How much space is required below 2" pipe to fit cell body. Can't find drawing with distances. View answer

Answer posted 5 years ago

Question 2

max amperage draw at 220v View answer

Answer posted 5 years ago

Question 3

I have an inground pool 13,500 gallon in southwest Florida what size SJ unit will i need ? View answer

Answer posted 5 years ago

Question 4

I have a RJ-45 Plus Salt Generator. I don't know what the winter mode button actually does and what it's usefulness is. The owners manual really doesn't describe it's function or why it should or should not be used. View answer

Answer posted 5 years ago

Question 5

What version should be on the Circupool Module for the SI 30. I believe mine is set on 9. View answer

Answer posted 5 years ago

Question 6

do you need to shock treat a pool with this Unit? Should non-chlorine shock be used? How often? View answer

Answer posted 5 years ago

Question 7

Cutting the cord is okay when replacing the collar cap. Or is there a way to disassemble the plug? View answer

Answer posted 5 years ago

Question 8

Can the CO2 injector be placed anywhere on the pressure side of the system after the pump? What about the pressure sensor? Note: I would only have one port available on the pump for use with this system. View answer

Answer posted 5 years ago | Sanitation > pH Control

Question 9

What's the minimum pressure required for the system to operate? What typical minimum RPM is needed with variable speed pumps? View answer

Answer posted 5 years ago | Sanitation > pH Control

Question 10

Need to get a manual. I own this device already View answer

Answer posted 5 years ago

Question 11

Is there a place where i can get actual dimensions? Like a shop drawing. Ive already managed to rule out the CORE55 from rough dimensions given to another. I suspect this model will be a much more close call on fitting. View answer

Answer posted 5 years ago

Question 12

All, I received my RJ-30 generator in the winter of 2019, installed for last season, this season I have been fighting with algae growth, and I think it is due to a defective flow sensor, is there some way I can clean it, or otherwise troubleshoot it before I have to replace the whole thing? I touched the wire on it today, and it stopped flickering with no-flow, and started generating again, so I am sure this is the issue. Please let me know, Louise View answer

Answer posted 5 years ago | Sanitation > Salt Chlorinators > RJ PLUS Series > CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources

Question 13

1. Is the Core55 UL listed? 2. Does the unit have a flow direction as the console might be facing my filter? 3. At full Chlorine output what is the 120/240 vac amperage (current draw)?? 4. Does the unit have a bonding lug for connection to the pool system grounded conductor? View answer

Answer posted 5 years ago

Question 14

What is the recommended GPM flow for the RJ45 system, Core35, and Core55 systems? View answer

Answer posted 5 years ago

Question 15

HI..MY SALT LEVEL PPM IS 5000. WILL YUR SYTEM STILL GENERATE CLHORILE AT THIS LEVEL? View answer

Answer posted 5 years ago

Question 16

DOES THE NO FLOW LIGHT STAY ON WHEN THE PUMP IS OFF? IF SO, HOW LONG? WILL I HAVE TO MANUALLY TURN IT OFF EVERY DAY? View answer

Answer posted 5 years ago

Question 17

Recommended set up on rj45 plus on 22000 gallon pool. Variable speed pump. Pump run time and percentage setting. Thanks View answer

Answer posted 5 years ago

Question 18

I currenty have a aquapure 1400 that I am really dissatisfied with. I just changed the cell and it is still sporadic with error messages. I can’t believe I just bought a cell for $700.00 and nothing! Is this system a direct bolt on? I don’t want to continue throwing money at this problem. The pool size is 18,000 gallons and I live in Miami, Fl. Which is hot! View answer

Answer posted 5 years ago

Question 19

Only number two polarity comes on View answer

Answer posted 5 years ago

Question 20

Did this take the place of the SGS salt system? View answer

Answer posted 5 years ago

Question 21

I just installed an RJ60+ in place of my Aquapure 1400. I was just wondering- on the unit, there is a “remote” indicator. What is this for? Are there ways to adjust the unit remotely, perhaps interfacing it with the Jandy system? Thanks. View answer

Answer posted 5 years ago

Question 22

What is the grams per hour output of the RJ45? View answer

Answer posted 5 years ago

Question 23

Does the RJ45 refer to pool size (45,000 Ga's) or does the 45 represent the element output in grams per hour? View answer

Answer posted 5 years ago

Question 24

I currently have a zodiac lm2-24 salt chlorinator. Does the Circupool sj-40 mount on the same plumbing? (i.e., have the same dimensions for its fittings? )or will I have to re-engineer the existing pvc? View answer

Answer posted 6 years ago

Question 25

Do you need to connect to a timer or will it turn on automatically when the pool pump is running while connected to the 110v outlet? View answer

Answer posted 6 years ago

Question 26

I have a SI series but don't know, manual doesn't say, if its a 30 or 45? I have a 18,000 gallon pool. is the -30 and -45 the same overall length? Connections to the controller the same? I don't want to replumb the system. Thanks. View answer

Answer posted 6 years ago

Question 27

Will any sand filter work with this system or do i need a newer sand filter? Mine is almost 25 years old. View answer

Answer posted 6 years ago

Question 28

Our GRC/J1400-3 chlorine generator has failed. Looking for a direct replacement so the pipes don't need to be changed. Is this model applicable? Thanks View answer

Answer posted 6 years ago

Question 29

Will this work on 24 round above ground pool that is 5 ft deep ? View answer

Answer posted 6 years ago

Question 30

I like the core55. I am currently a no salt pool and would like to switch with this system. However, my pool is 54,000 gallons. Can I install the core55 with any the core35 and meet my needs? View answer

Answer posted 6 years ago

Question 31

we just recently bought this product and have questions. Is there a customer service department we can speak to? View answer

Answer posted 6 years ago

Question 32

Standard overall needed space for installation? And can it be installed vertically? View answer

Answer posted 6 years ago

Question 33

what is the length of it? How long of a span of tubing is needed to be cut out for install? View answer

Answer posted 6 years ago

Question 34

The Digital Control Panel of the SJ-40 has stopped working how can I fix it? View answer

Answer posted 6 years ago

Question 35

Will the system say when it’s time to change the cell? View answer

Answer posted 6 years ago

Question 36

IS THIS A 110V UNIT ? View answer

Answer posted 6 years ago

Question 37

Can the universal system be used to replace a traditional chlorine pool? What is the difference between this and the RJ system? View answer

Answer posted 6 years ago

Question 38

What is the length of the power cord? View answer

Answer posted 6 years ago

Question 39

1.Is there a video showing how to install? 2.Also, I have a 30,000 gallon pool, is it better to oversized the salt chlorinate? 3. I am replacing an existing chlorinator, I am very familiar with working with PVC pipe, is this a DIY project? 4. If I install myself are all warranties still in effect. Thank you View answer

Answer posted 6 years ago

Question 40

I have a SJ-series system 4 years ago. works great. I just had a variable speed pool pump installed. It goes threw its own internal timers. does the SJ- series have a built in flow switch sensor built in. Worried about the unit coming on via the old pool timer without the new pump running? View answer

Answer posted 6 years ago

Question 41

I am replacing a Hayward system. I will eventually replace the control panel also but for now need ot know if I need to purchase anything else to connect to the existing control panel. it has a plug that connects to it now. Do I need to purchase a separate plug to connect to the control panel? View answer

Answer posted 6 years ago

Question 42

Can this be used on an above ground pool? View answer

Answer posted 6 years ago

Question 43

Interested in purchasing this with a variable speed pump and saltwater generator. I understand the saltwater generator can be wired to constant power and will be activated by the flow switch. How do I control the Ozone Generator operation in this setup? View answer

Answer posted 6 years ago

Question 44

I have purchased 2 of your RJ 30 units in the past for my pool. I really like the product and need a RJ 20 for my daughter . I have noticed the prices have increased substantially since my last purchase. There are many places that sell this product, which has the best price ? Also, what is the 120 v for $18.50 do. What is its purpose when the system runs on low voltage? Are there any discounts ? Military, senior anything at all . Thank you View answer

Answer posted 6 years ago

Question 45

Who sells and installs the EDGE 25/40 in Orlando Florida Area? View answer

Answer posted 6 years ago

Question 46

What is the total dimension for the flow switch and cell for the Edge 40? 11 3/4 inches View answer

Answer posted 6 years ago

Question 47

What are the overall dimensions of the unit? View answer

Answer posted 6 years ago

Question 48

If hardwired to the pump, will the percentage of output stay the same when powered off and back on again? View answer

Answer posted 6 years ago

Question 49

What is the recommendation for operations of this system over the winter months in north Texas. Should the system be maintained and in operation or turned off? View answer

Answer posted 6 years ago | Sanitation > pH Control

Question 50

What determins when your RJ+45 Series" goes into it's "REST Cycle"? View answer

Answer posted 6 years ago

Sanitation Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic

Tools