Sanitation Q&A

Question 1

Clarification about the cell-cleaning, acid:water ratio. View answer

Asked 1 ´year ago

Question 2

Does the flow direction matter with salt cell? View answer

Asked 10 ´months ago

Question 3

How do I clean the CircuPool RJ45+ salt cell? View answer

Asked 3 ´years ago | Support

Question 4

mPo / Temp:eNo View answer

Asked 10 ´months ago | Sanitation > Salt Chlorinators > RJ PLUS Series > CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources

Question 5

Why is salt level reading not accurate? View answer

Asked 3 ´years ago | Support

Question 6

What is the Warranty on an RJ45 View answer

Asked 8 ´months ago | Sanitation > Salt Chlorinators > RJ PLUS Series > CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources

Question 7

How do you recalibrate the salt monitoring system View answer

Asked 1 ´year ago | Sanitation > Salt Chlorinators > Universal Series > CircuPool Universal Series Salt Chlorine Generators - Owner Resources

Question 8

How do you replace the fuse? View answer

Asked 2 ´years ago | Sanitation > Salt Chlorinators > RJ PLUS Series > CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources

Question 9

Can't find replacement for flow switch View answer

Asked 10 ´months ago

Question 10

Can the RJ+ cell be installed in a vertical section of return pipe (not using your loop method)? View answer

Asked 9 ´days ago | Sanitation > Salt Chlorinators > RJ PLUS Series > CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources

Question 11

Can I add the remote control and balance monitoring to an RJ-60+ unit or do I need to switch to the CORE line? View answer

Asked 10 ´months ago

Question 12

Is the cell a direct replacement for the Pentair IC20? And, is the flowmeter integral it the cell? View answer

Asked 4 ´years ago

Question 13

How do you know if your flow switch is bad? View answer

Asked 10 ´months ago | Support

Question 14

Temperature sensor incorrect View answer

Asked 2 ´years ago | Sanitation > Salt Chlorinators > RJ PLUS Series > CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources

Question 15

I just ordered an RJ-45+. Should I install a check valve after the heater? View answer

Asked 3 ´years ago

Question 16

Stops generating after a few hours of running. Turn it off and on and back to normal. View answer

Asked 1 ´year ago

Question 17

Salinity reads 0000 View answer

Asked 10 ´months ago

Question 18

How do I reset cell maintenance light after cleaning it? View answer

Asked 1 ´year ago | Sanitation > Salt Chlorinators > Universal Series > CircuPool Universal Series Salt Chlorine Generators - Owner Resources

Question 19

Is the flow switch required on a salt chlorinator system? View answer

Asked 3 ´years ago

Question 20

How to clean salt cell on CircuPool CORE? View answer

Asked 3 ´years ago

Question 21

My salt chlorinator control panel has started to make a buzzing sound for the first hour of operation. View answer

Asked 1 ´year ago | Sanitation > Salt Chlorinators > Universal Series > CircuPool Universal Series Salt Chlorine Generators - Owner Resources

Question 22

How often do I need to replace the salt cell and how much does it cost? View answer

Asked 11 ´months ago

Question 23

RJ-60 Plus does the direction of flow through the cell matter? View answer

Asked 2 ´years ago | Support

Question 24

How do I connect the CircuPool RJ-PLUS salt chlorinator to a timer? View answer

Asked 1 ´year ago

Question 25

Which way around do you install the salt cell? View answer

Asked 11 ´months ago

Question 26

Controller orientation View answer

Asked 2 ´years ago | Sanitation > Salt Chlorinators > CORE Series > CircuPool CORE Series Salt Chlorine Generators - Owner Resources

Question 27

Salt reading 0000 what does that mean . Light is on power and light is on generating but reading 0000 View answer

Asked 10 ´months ago | Sanitation > Salt Chlorinators > Universal Series > CircuPool Universal Series Salt Chlorine Generators - Owner Resources

Question 28

No lights on the panel View answer

Asked 1 ´year ago | Sanitation > Salt Chlorinators > SJ Series > CircuPool SJ-A Series Salt Chlorine Generators - Owner Resources

Question 29

I have a timer on my pump. Does the generator need to be on a timer also or is it ok to just let the flow switch shut down the unit when the pump is off? View answer

Asked 3 ´years ago

Question 30

What would be the preferred operating setup (to promote cell life): 12 hours at 25% output or 6 hours at 50%? View answer

Asked 1 ´year ago

Question 31

Salt generator is detecting no flow but the paddle is working properly, what is the fix View answer

Asked 9 ´months ago

Question 32

I have a high water temp message on the display. What needs done to fix this? View answer

Asked 2 ´years ago | Sanitation > Salt Chlorinators > RJ PLUS Series > CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources

Question 33

flow switch not working View answer

Asked 3 ´years ago

Question 34

My RJ45 temperature displays high at 168.9 degree but my water temperature is only 57 degrees View answer

Asked 1 ´year ago

Question 35

what size pipe is used for the inlet and outlet and is it PVC? View answer

Asked 3 ´years ago

Question 36

I have done a cell cleaning on RJ60+ about 2 weeks ago, now I get message to do again View answer

Asked 9 ´months ago | Sanitation > Salt Chlorinators > RJ PLUS Series

Question 37

Does it hurt the salt generator to be running when the pump is off and no water going through? View answer

Asked 2 ´years ago | Sanitation > Salt Chlorinators > RJ PLUS Series > CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources

Question 38

Salinity level display View answer

Asked 10 ´months ago | Sanitation > Salt Chlorinators > Universal Series > CircuPool Universal Series Salt Chlorine Generators - Owner Resources

Question 39

Optimal salt level in ppm for this device View answer

Asked 6 ´months ago | Sanitation > Salt Chlorinators > CORE Series > CircuPool CORE Series Salt Chlorine Generators - Owner Resources

Question 40

Can you provide an installation manual for the CircuPool CORE Salt Chlorinator? View answer

Asked 10 ´months ago

Question 41

What does it mean when the display says COLD View answer

Asked 2 ´years ago

Question 42

I have been underwhelmed with the Aqualink TCX system. Will your 2026 complete control be able to replace Jandy TCX View answer

Asked 10 ´months ago

Question 43

My NO FLOW light started flashing, shut unit down & checked flow switch, restarted now is solid red View answer

Asked 1 ´year ago | Sanitation > Salt Chlorinators > RJ PLUS Series > CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources

Question 44

How do you claim a warranty on my CircuPool equipment? View answer

Asked 3 ´years ago

Question 45

How long is the salt generator supposed to last? I just recently cleaned mine as instructed reinstalled and it stop View answer

Asked 1 ´year ago | Sanitation > Salt Chlorinators > EDGE Series > CircuPool EDGE Series Salt Chlorine Generators - Owner Resources

Question 46

How to calibrate salinity reading View answer

Asked 2 ´years ago | Sanitation > Salt Chlorinators > Universal Series > CircuPool Universal Series Salt Chlorine Generators - Owner Resources

Question 47

Flow and low temperature LEDs both red View answer

Asked 10 ´months ago | Sanitation > Salt Chlorinators > SJ Series > CircuPool SJ-A Series Salt Chlorine Generators - Owner Resources

Question 48

I have the RJ 30 plus. can i replace the cell with the Rj + 45 cell replacement View answer

Asked 11 ´months ago

Question 49

Chlorinator worked last year but this year works for a few minutes then red light for cell and salt lights up. View answer

Asked 10 ´months ago | Sanitation > Salt Chlorinators > SJ Series > CircuPool SJ-A Series Salt Chlorine Generators - Owner Resources

Question 50

Does this install before or after the salt generator? View answer

Asked 1 ´month ago

Sanitation Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic

Tools