Question 1

I am replacing a Hayward system. I will eventually replace the control panel also but for now need ot know if I need to purchase anything else to connect to the existing control panel. it has a plug that connects to it now. Do I need to purchase a separate plug to connect to the control panel? View answer

Asked 4 ´years ago

Question 2

I have a limited length of 2" pipe to install the generator. What is the length of pipe needed to be cut out for install? Does the unit come with a cut template? View answer

Asked 3 ´years ago

Question 3

Can this be used for an 8’x8’ below ground hot tub? View answer

Asked 3 ´years ago

Question 4

What is the length of the EDG40 chlorine generator cell, please? Just end-of-threads-to-end-of-threads... View answer

Asked 3 ´years ago

Question 5

On the edge40 for do it yourselfer does this just plug into a gfci outlet. I cant find the installation instructions. I have a small pool maybe 10000-12000 gal. View answer

Asked 3 ´years ago

Question 6

What is the power draw on the Edge system? View answer

Asked 2 ´years ago

Question 7

I have a 10,000 gallon pool and want to convert to salt. So many questions. It's been 3 years since I drained and replaced 1/2 the water in the pool due to a repair. Should I consider a water replacement prior to conversion ? Under what circumstances should I consider water replacement? Money not an option...which model should I buy? What size? When does increase size not benefit performance for salt conversion power, cell cleaning cycle time, and cell life? Installation should not be a consideration as all would fit my system. Thank you, Bill View answer

Asked 2 ´years ago

Question 8

How do I winterize with this system. View answer

Asked 3 ´years ago

Question 9

What is the voltage for the chlorinator View answer

Asked 1 ´year ago | Sanitation > Salt Chlorinators > SJ Series > CircuPool SJ-A Series Salt Chlorine Generators - Owner Resources

Question 10

Why does the boost light flash on my edge pool generator? View answer

Asked 2 ´years ago

Question 11

Why is the salinity average always lower than instant level? View answer

Asked 1 ´year ago | Support

Question 12

I reversed the cleaning amounts using more acid than water. Did i destroy the unit ? View answer

Asked 3 ´years ago

Question 13

What is the expected lifespan of the CORE55 Replacement Cell. How does the eight year warranty impact the cost of replacing the cell if it applies at all? View answer

Asked 2 ´years ago

Question 14

My core 55 is only showing one bar and if I increase the bars, it one flashes on another bar. It also says to clean the unit which I have done several times. What can I do to fix the problem. At first, it was working great. View answer

Asked 2 ´years ago

Question 15

I would like to have some installation instructions for this item View answer

Asked 2 ´years ago

Question 16

What are the specific sizes of each of the 3 O rings? Where does each of the 3 O rings go? What are the instructions for replacing an O rings? Are any other parts needed? View answer

Asked 3 ´years ago

Question 17

I have an RJ 30 and need replacement "O" rings one for each end. Not sure the 3 you show fit my unit (purchased 2/2016). Please advise. Part number and cost. View answer

Asked 3 ´years ago

Question 18

How is the cable installed any cutting required? View answer

Asked 5 ´years ago

Question 19

Which terminal on the circuit board does the blue wire connect too ? Foolish me forgot to mark it when removing. View answer

Asked 4 ´years ago

Question 20

where can buy the maie end of a cicircopool salt generator View answer

Asked 3 ´years ago

Question 21

You only show one end of the cord. Does the other end have the threaded part that screws into the RJ-45 unit? View answer

Asked 5 ´years ago

Question 22

Will this repair the Rj systems ? View answer

Asked 5 ´years ago

Question 23

where is reset button located on rj 45? My serial number is 030255 View answer

Asked 3 ´years ago

Question 24

How do u replace a fuse on the RJ30 CircuPool salt system. Icant see how u open case. System comes on then turns off and light % dims on and off. View answer

Asked 3 ´years ago

Question 25

Only top line of text is appearing and then a small portion of it in missing. Will replacing the keypad fix this issue? View answer

Asked 5 ´years ago

Question 26

Do this part fits on a power module serial 130273? View answer

Asked 5 ´years ago

Question 27

My keypad no longer is working. Nothing is displayed. How do I replace it? View answer

Asked 5 ´years ago

Question 28

where can i get a replacement keypad for the JS series unit? View answer

Asked 4 ´years ago

Question 29

The keypad is showing output-off when I reset by pressing the + key and bring it up to 60 or 80, but in a few minutes or couple hours is back on output-off, Do I need a new keypad or a new circuit board? thank you View answer

Asked 4 ´years ago

Question 30

I have a rj 45 classic the it had on panel.power off and will not turn on will the key pad help this or do u need a whole new control panel View answer

Asked 3 ´years ago

Question 31

Is the screen replaceable? I did not see in on the site. View answer

Asked 2 ´years ago

Question 32

Is there a replacement cable for the RJ series which connects the controller to the cell? I believe my blue connector has failed. View answer

Asked 5 ´years ago

Question 33

Hello, the Replacement Union looks like the part I need but I'm unsure. I do have a classic RJ system. The part I need fills the open end of the clear cylinder. It also hold the electrodes. I also need the bolts and male electrodes, and the rubber o ring. I would also like to buy a replacement electrical cord with the female red, black, and blue connectors attached. Could you please supply part number so I can order?Thank you, Rih Kosina View answer

Asked 5 ´years ago

Question 34

RJ-60 Plus does the direction of flow through the cell matter? View answer

Asked 1 ´year ago | Support

Question 35

I have a RJ 60 PLUS...........Will this fit my cell? What is 3rd generation? View answer

Asked 2 ´years ago

Question 36

Will this product bypass my Hayward W3T-CELL-15 TurboCell Salt Chlorination Cell? View answer

Asked 1 ´year ago

Question 37

Is this the correct 2" cell union for a RJ30+ system? View answer

Asked 3 ´years ago

Question 38

Should the power cord from control box to timer be routed in conduit? View answer

Asked 1 ´year ago | Sanitation > Salt Chlorinators > RJ PLUS Series > CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources

Question 39

Looking for replacement unions and O-rings for RJ-45+ What is the part number? View answer

Asked 3 ´years ago

Question 40

does this come as one or both pieces View answer

Asked 3 ´years ago

Question 41

I have a rjjc+30, sn 05a75da4d1850010, I need a replacement union, I do not know if it is a 3rd generation or not. Please advise. Thanks, Mark Goodrich View answer

Asked 2 ´years ago

Question 42

I am reinstalling my RJ60+ because of leaks. Is this union the same as the one that came with my RJ60+. Does it a a groove cut in it for the o-ring? View answer

Asked 2 ´years ago

Question 43

Does this fit RJ30? Also, where is it located and how do you remove old one? View answer

Asked 2 ´years ago

Question 44

Is the CircuPool® Replacement Union sold as a single piece or as a pair? View answer

Asked 3 ´years ago

Question 45

I have a Circupool Model Si30. I have the cell with the female part of the union the replacement did not come with the inside part that glues to the pipe. I need the adapters at 1-1/2". What item # would I need? View answer

Asked 2 ´years ago

Question 46

Is this the main board for the chlorine generator. View answer

Asked 3 ´years ago

Question 47

Is the circuit board for a CircuPool Universal Series??? View answer

Asked 2 ´years ago

Question 48

I need a new enclosure box as well as the PCB. Is this available and cost? View answer

Asked 2 ´years ago

Question 49

I have an AquaRite Model: AQ-RITE-X295; SN 5A0710-1047242, rev 1.4. Can I replace the blown circuit board with your CircuPool Si PCB? View answer

Asked 2 ´years ago

Question 50

My current Si controller will not index when the button is pushed. Will this fix the problem or do I need the other board? View answer

Asked 2 ´years ago

Browse by Topic

Tools