Question 1

I am reinstalling my RJ60+ because of leaks. Is this union the same as the one that came with my RJ60+. Does it a a groove cut in it for the o-ring? View answer

Asked 3 ´years ago

Question 2

Can I install flow switch vertically before cell if cell is installed horizontally? View answer

Asked 2 ´years ago

Question 3

The “Cell Connection “ comes up on the display and nothing works View answer

Asked 2 ´years ago | Sanitation > Salt Chlorinators > RJ PLUS Series > CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources

Question 4

Can the convertor cell be mounted vertically and the flow detector be mounted on the adjacent horizontal run ? What horizontal straight tube length should precede the flow device along the horizontal tube run ? View answer

Asked 5 ´years ago

Question 5

What is the water flow direction thru the cell View answer

Asked 5 ´years ago

Question 6

I have a rjjc+30, sn 05a75da4d1850010, I need a replacement union, I do not know if it is a 3rd generation or not. Please advise. Thanks, Mark Goodrich View answer

Asked 4 ´years ago

Question 7

Is model UL55 have a NSF50 certification? View answer

Asked 7 ´months ago | Sanitation > Salt Chlorinators > Universal Series > CircuPool Universal Series Salt Chlorine Generators - Owner Resources

Question 8

I just purchased RJ60+ System. Is there a maximum flow limit that I shall not exceed for the Salt Cell.? Maximum flow, for example 85 GPM, for their Salt Cell. View answer

Asked 3 ´years ago

Question 9

no flow light View answer

Asked 1 ´year ago

Question 10

Hello. I have an RJ-60+ which is rated at 300W, so presumably it only draws 1.36A at 220V. However, the manual also mentions the cell current ranging between 2.5 and 7.8 amps. I can also see the cell current displayed when I cycle through the menu options. For example, at 50%, it shows 5.7 amps. I'm assuming this cell current is different from the load on the circuit breaker. Can you confirm please? View answer

Asked 4 ´years ago

Question 11

Cleaning Cap for RJ45+ View answer

Asked 2 ´years ago | Cleaners

Question 12

Hello, I have just purchased the RJ-30 Plus Salt system, and wanted to know it's power usage in Watts and Amps. Also, is it more efficient to connect it to 220v vs. 120v, and if so, how much more efficient? Whats the amperage & wattage for 220v vs. 120v connections? Thank you! View answer

Asked 4 ´years ago

Question 13

I have”STo” on my display View answer

Asked 8 ´months ago | Replacement Cells > Aftermarket Replacement Cells <span>fitting Hayward® / Goldline®</span>

Question 14

Not all the sediment is leaving the sediment chamber after using the purge valve. View answer

Asked 8 ´months ago | Support

Question 15

Will this filter out pollen? View answer

Asked 11 ´months ago

Question 16

Is this the main board for the chlorine generator. View answer

Asked 4 ´years ago

Question 17

when there is no electricity, will the device return to work after the power is restored? View answer

Asked 3 ´years ago

Question 18

The only power source available is 240 volt. Can the core 35 be rewired for a 240 volt connection? View answer

Asked 4 ´years ago

Question 19

Can the core 35 be rewired for a 240 volt connection View answer

Asked 11 ´months ago | Sanitation > Salt Chlorinators > CORE Series > CircuPool CORE Series Salt Chlorine Generators - Owner Resources

Question 20

Is the circuit board for a CircuPool Universal Series??? View answer

Asked 4 ´years ago

Question 21

Where does the print go on the winter cap. It seems to be placed on the top and outside of cap but it leaks. So should it be on the inside when installing View answer

Asked 4 ´years ago

Question 22

Chlorine is not being generated. New cell with about 6 months service. Will a problem with the small board not indexing causing this problem? View answer

Asked 4 ´years ago

Question 23

Is the screen replaceable? I did not see in on the site. View answer

Asked 3 ´years ago

Question 24

If I currently have a Hayward Aquarite, do I need the adapter or will the Core35 fit where my cell is now? View answer

Asked 3 ´years ago

Question 25

Part Number: RJ20N-3300-7A I am not able to order this product. Is it out of stock? View answer

Asked 11 ´months ago | Sanitation > Salt Chlorinators > RJ PLUS Series > CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources

Question 26

Is this the ORing that goes in the Union Nut to seal against the Face of the Generator? View answer

Asked 4 ´years ago

Question 27

RJ PLUS Keypad View answer

Asked 11 ´months ago

Question 28

Is there a replacement cable for the RJ series which connects the controller to the cell? I believe my blue connector has failed. View answer

Asked 6 ´years ago

Question 29

Hello, I have a 6,000 gal in-ground pool in the Florida Keys. What is the best system and size for my pool. thank you. Jose View answer

Asked 3 ´years ago

Question 30

What is the wording for the limited warranty * ? View answer

Asked 3 ´years ago

Question 31

The keypad is showing output-off when I reset by pressing the + key and bring it up to 60 or 80, but in a few minutes or couple hours is back on output-off, Do I need a new keypad or a new circuit board? thank you View answer

Asked 5 ´years ago

Question 32

CircuPool Gen9 connection pins are different from my original Hayward View answer

Asked 11 ´months ago | Support

Question 33

My current Si controller will not index when the button is pushed. Will this fix the problem or do I need the other board? View answer

Asked 4 ´years ago

Question 34

What size RJ generator system would you recommend ??? View answer

Asked 3 ´years ago | Sanitation > Salt Chlorinators > RJ PLUS Series

Question 35

Is the CircuPool® Replacement Union sold as a single piece or as a pair? View answer

Asked 4 ´years ago

Question 36

Can I replace my old RJ salt system which has a different shaped cell with this one? View answer

Asked 3 ´years ago

Question 37

We're thinking of replacing out Hayward with this system. Can we reply on the flow switch to turn the chlorinator on and off? The pump is always powered, but has an internal controller as well as variable speed. We can have reduced flow as well as no flow during parts of the day. Will this hurt your system? Thank you in advance. View answer

Asked 3 ´years ago

Question 38

Is this the right 2" union for a RJ +? View answer

Asked 5 ´years ago

Question 39

Please can you provide a technical drawing for this. Looking to replace a Surechlor 3000 SC210 and need to compare sizes/threads/fittings etc. thanks in advance, Gary View answer

Asked 3 ´years ago

Question 40

Can I use a copper-based algaecide in my pool? View answer

Asked 11 ´months ago

Question 41

Does this fit all SJ series? If not, refundable? View answer

Asked 3 ´years ago

Question 42

does it fit for sj40 series? View answer

Asked 4 ´years ago

Question 43

Does this fit RJ30? Also, where is it located and how do you remove old one? View answer

Asked 3 ´years ago

Question 44

Can rj60 be powered from pentair intelliflo3 vsp built in 5 amp relay View answer

Asked 11 ´months ago | Support

Question 45

I have purchased a Core 35 to convert my Fiberglass inground pool to salt water for 2023. View answer

Asked 3 ´years ago | Sanitation > Salt Chlorinators > CORE Series

Question 46

Last year, on my 5 year old CircuPool RJ45, the buttons only half worked. But it made chlorine - now, no chlorine. View answer

Asked 11 ´months ago | Sanitation > Salt Chlorinators > RJ PLUS Series

Question 47

What size plumbing is this compatible with? View answer

Asked 3 ´years ago

Question 48

Does the CircuPool Core 35 come with a sacrificial anode? View answer

Asked 3 ´years ago

Question 49

Is the warranty for 8 years even if I install it the owner and it’s large enough for 80 thousand litres pooland brand new unit and will I receive it and is in Canadian money this numbe thanks View answer

Asked 3 ´years ago

Question 50

"Roughly" how long is the power wire? If it's short, is it easy to wire in a new one? "Roughly" how many amps would one think the 35k unit draws? I'm deciding on hardwiring it to my pump timer or a separate GFI outlet that runs off the timer. View answer

Asked 3 ´years ago

Browse by Topic

Tools