CircuPool RJ-PLUS Series Salt Chlorine GeneratorsOwner Resources Questions & Answers

How can I tell when my electrolytic cell is bad? View answer

Asked 1 ´year ago

How do I clean the CircuPool RJ45+ salt cell? View answer

Asked 3 ´years ago | Support

Clarification about the cell-cleaning, acid:water ratio. View answer

Asked 1 ´year ago

Low Temp View answer

Asked 1 ´year ago

Do I need to register View answer

Asked 1 ´year ago

Why does it show no cell match? View answer

Asked 6 ´months ago

What do I do when the cell maintenance light is on my CircuPool RJ45+ salt chlorine generator? View answer

Asked 3 ´years ago

Cell connection View answer

Asked 6 ´months ago

Why is salt level reading not accurate? View answer

Asked 3 ´years ago | Support

My NO FLOW light started flashing, shut unit down & checked flow switch, restarted now is solid red View answer

Asked 1 ´year ago

RJ60+ reading a voltage (around 28) but zero salinity and amps View answer

Asked 2 ´years ago

What is the typical life of a salt cell? View answer

Asked 1 ´year ago

High salt View answer

Asked 2 ´years ago

My salt cell is creating foam in my pool View answer

Asked 1 ´year ago

No flow solid red light View answer

Asked 9 ´months ago

Menu button not working View answer

Asked 10 ´months ago

Rj60 View answer

Asked 11 ´months ago

No flow View answer

Asked 11 ´months ago

Where is the reset button in the CircuPool RJ-PLUS Series Salt Chlorine Generators? (circupool rj45+ manual) View answer

Asked 2 ´years ago

How do i get replacement parts under warranty? View answer

Asked 10 ´months ago

No keys on controller respond and display reads "cell connection." View answer

Asked 1 ´year ago

"Cell Connection" locks up display and controls. My understanding there is a module addition to fix this issue ? View answer

Asked 1 ´year ago

My RJ-45 is showing negative amps View answer

Asked 1 ´year ago

Why does my rj30+ read "Temp peNo" and the green power light flashes? View answer

Asked 10 ´months ago

“Cell connection” View answer

Asked 9 ´months ago

Does the flow direction matter with salt cell? View answer

Asked 9 ´months ago

Do the salt generator plates need to be fully submerged at all times? View answer

Asked 9 ´months ago

How do you replace the fuse? View answer

Asked 2 ´years ago

I have never seen a positive current reading from the menu. What's wrong? View answer

Asked 2 ´years ago

mPo / Temp:eNo View answer

Asked 9 ´months ago

Can get my system past “Cell Connection” View answer

Asked 10 ´months ago

Buttons not working View answer

Asked 8 ´months ago

The control panel on my RJ plus does not cycle through the menu. View answer

Asked 1 ´year ago

how acccurate is the control unit salinity reading? View answer

Asked 2 ´years ago

How do you access the Internal jumpers View answer

Asked 9 ´months ago

Where can I find the CircuPool serial number on my equipment?? View answer

Asked 2 ´years ago

I Can't Raise the Output on my CircuPool RJ 45+ View answer

Asked 1 ´year ago

When adding salt for maintenance reasons should I turn off the SWG for a period of time? View answer

Asked 2 ´years ago

Salt level ok, generator cleaned, but chlorine levels remain extremely low View answer

Asked 8 ´months ago

what is the position of the data jumper? View answer

Asked 1 ´year ago

Why does display show temp high message when trying to adjust chlorinator? Our water temperature is around 83 View answer

Asked 2 ´years ago

Why does my display say "LOW TEMP" and not generating....says water temp is 46 degrees and my Jandy says its 78 deg View answer

Asked 1 ´year ago

what are dimensions of control box. RJ-30 I want to mount it on the circuit breaker panel. View answer

Asked 3 ´years ago

The water temp in the pool is 86 degrees and the temp high shown on the power unit is 160F. This is not possible. W View answer

Asked 7 ´months ago

Salt cell is clogged within a week View answer

Asked 7 ´months ago

I just installed an RJ60+ in place of my Aquapure 1400. I was just wondering- on the unit, there is a “remote” indicator. What is this for? Are there ways to adjust the unit remotely, perhaps interfacing it with the Jandy system? Thanks. View answer

Asked 5 ´years ago

Cell connection View answer

Asked 1 ´year ago

No amps View answer

Asked 1 ´year ago

My screen is not working View answer

Asked 1 ´year ago

Screen is frozen with "cell connection " error message. It won't turn off by pushing the button. Warranty coverage? View answer

Asked 1 ´year ago

CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources Q&A

Activity timeframe

View More Product Details

Related Product

Browse by Topic

Tools