CircuPool Universal Series Salt Chlorine GeneratorsOwner Resources Questions & Answers

Maintence light and low salt cont. on, cell cleaned, salt levels tested normals View answer

Asked 1 ´month ago

sacrificial anode / cyanuric acid stabilizer level in pool? View answer

Asked 3 ´years ago

How do i reset the flashing cell maintenance light? View answer

Asked 2 ´years ago

To prolong the life of a salt water chlorine generator's cell, would it be better to run the pool system at 25% for 24 hrs., 50% for 12 hrs. or 100% 6 hrs View answer

Asked 2 ´months ago

How do you recalibrate the salt monitoring system View answer

Asked 2 ´years ago

Unit appears wired for 220 yet the wire colors are black white and green. Code says black red and green. View answer

Asked 2 ´years ago

My flow switch continues to flash View answer

Asked 1 ´month ago

Where can I find the CircuPool serial number on my equipment?? View answer

Asked 2 ´years ago

I have an Si-30+ saltwater chlorinator. Will the Si-30 electrode replace my old cell? View answer

Asked 2 ´years ago

Can you tell me which replacement cell I ordered last? View answer

Asked 1 ´year ago

Why does my cell seem to be not making chlorine? View answer

Asked 1 ´year ago

How do I reset cell maintenance light after cleaning it? View answer

Asked 1 ´year ago

Salt reading 0000 View answer

Asked 3 ´years ago

MY UL25 model screen has the two left lights green, no salt is red and clean cell is yellow. Display says 3508. View answer

Asked 2 ´months ago

What is the various data on the screen? View answer

Asked 1 ´year ago

no flow light View answer

Asked 2 ´years ago

I have an error message 'hot'. I found that it indicates a faulty flow switch. I replaced with a new one. no luck View answer

Asked 1 ´year ago

I got a salt cell in February. I am adding salt twice a week and after about three days I start to see loose alg View answer

Asked 3 ´years ago

Universal cell 40 View answer

Asked 1 ´month ago

I need a "Cleaning Cap" or a "Cleaning Stand" for CircuPool Universal Series Salt System Models UL25 View answer

Asked 1 ´month ago

Do I need to register my new system and if so, where do I register it at? View answer

Asked 2 ´years ago

testing a salt cell View answer

Asked 2 ´years ago

Why does the chlorine light blinking View answer

Asked 7 ´months ago

Where do you install the cartridge-looking device... On the intake line or the outflow (back to the pool) line? View answer

Asked 4 ´years ago

Why not sell the flow switch with the Tee? But you you show the sensor with the tee to sell the sensor. View answer

Asked 2 ´years ago

I need a new salt cell it's still under warranty View answer

Asked 1 ´year ago

What version should be on the Circupool Module for the SI 30. I believe mine is set on 9. View answer

Asked 5 ´years ago

Does the wire to the salt generator control module disconnect from the generator cell? View answer

Asked 3 ´years ago

I have an Si 30 salt cell can I use a different brand to replace the cell? View answer

Asked 1 ´year ago

Where is the serial number located? View answer

Asked 2 ´years ago

What is the recommended breaker size for a 240 volt installation? View answer

Asked 2 ´years ago

How can I test the flow switch on CircuPool RJ-PLUS or Universal Series? View answer

Asked 1 ´month ago

How often is my salt cell supposed to be cleaned? View answer

Asked 2 ´months ago

I have the UL80. When the filter goes on, I see a a cloudy substance coming out of the discharge. What is this View answer

Asked 5 ´months ago

My salt is 4482 ppm but the system will not produce chlorine. Its been installed for 2 weeks with no luck in prod

Asked 4 ´months ago

With a variable speed pump is it ok to leave the generator powered all the time even when the pump shuts off View answer

Asked 3 ´years ago

Does the Universal55 have the same threads as Hayward Goldline Aqua Rite? I.e., can I unscrew the Hayward and xxxx in the Universal? Or is it the length that is what makes them 'compatible' per the webpage description? Thanks much. View answer

Asked 4 ´years ago

how to find type of unit cell in my system? View answer

Asked 3 ´years ago

mineral build up in cell

Asked 3 ´months ago

My Sr-60 generator failed. The Cell is newer, and should not need to be replaced. How much for a replacement gen View answer

Asked 2 ´years ago

Can i purchase just the control module for a CircuPool Universal Series / SI Series unit? View answer

Asked 3 ´years ago

My generator panel is making a loud grinding sound like the power supply fan is dying. View answer

Asked 2 ´years ago

Can I mount this vertically if the pipe is long enough? View answer

Asked 5 ´months ago

My cleaning light continues to flash it will not stop when I hold the reset button in for 10 seconds. I have cleane View answer

Asked 2 ´years ago

"Hot" error message. View answer

Asked 2 ´years ago

Does the control module need constant electrical power, or could it be plugged into a timer and powered intermittently? View answer

Asked 1 ´year ago

I bought an Si 40 system 1 month ago. I get Slo error even tho salt ppm is 3500. View answer

Asked 3 ´years ago

Hello, my circupool chlorinator is not producing chlorine and registers hot View answer

Asked 1 ´year ago

Generating light stays on View answer

Asked 1 ´year ago

is it plug and play 120 volt input hook-up. is it all in one inside program box is there a transformer inside the panel? or do I need extural View answer

Asked 4 ´years ago

CircuPool Universal Series Salt Chlorine Generators - Owner Resources Q&A

Activity timeframe

View More Product Details

Related Product

Browse by Topic

Tools