Question 1

Do these o-rings fit the RJ+30 Chlorinator? View answer

Answer posted 2 years ago | CircuPool® O-Ring Set for RJN/UL/Si

Question 2

My pool is 35k gals does it hurt anything if I go with the bigger 55k unit? Thanks View answer

Answer posted 3 years ago

Question 3

When converting from a chlorine pool to this system, do I run the already chlorinated water through the system and add additional salt as needed? Thanks a lot for the assistance. View answer

Answer posted 3 years ago

Question 4

Will this fit a Circupool Universal 25? View answer

Answer posted 3 years ago | CircuPool® Cleaning Stand for CircuPool RJ Plus, Universal, and Si Systems

Question 5

Does this 0-ring fit the electolytic cell for the CircuPool Core 35 unit? View answer

Answer posted 3 years ago

Question 6

does ring fit inside the cap? View answer

Answer posted 3 years ago

Question 7

Does this fit on the circupool universal25 salt chlorine generator? View answer

Answer posted 3 years ago

Question 8

I bought a house with a 26qft pool. I'm trying to learn to control the salt chlorinator (SJ series) for my pool. The water is murky now, with algae. All parameters are ok (I check regularly), except chlorine and free chlorine levels, which are at 0. How do I know that the cell actually works? Is there a documentation regarding the controller? the left bottom green light has been blinking. Also, how is this controller related to the pump? I have Hayward controller for the pump, and I'm clueless here too. Please help. View answer

Answer posted 3 years ago

Question 9

What size is the cap. The threaded part View answer

Answer posted 3 years ago | CircuPool® Cleaning Stand for CircuPool RJ Plus, Universal, and Si Systems

Question 10

Is the warranty for 8 years even if I install it the owner and it’s large enough for 80 thousand litres pooland brand new unit and will I receive it and is in Canadian money this numbe thanks View answer

Answer posted 3 years ago

Question 11

Would this pump be a swap out for a Pentair 1.5 or would pipe modifications be needed? And can it be used with fresh water chlorine pools? View answer

Answer posted 3 years ago

Question 12

I have a variable speed pump and I'm curious, what is the minimum water flow in GPM for the CORE series? View answer

Answer posted 3 years ago

Question 13

Installed in fall of 2020. Tuned on in spring of 2021. How do I clean it and what is best to use. ??? View answer

Answer posted 3 years ago

Question 14

Is it OK to install the salt generator cell (SJ-20) and flow sensor on the discharge piping of my pool cartridge cannister? View answer

Answer posted 3 years ago

Question 15

Since the SJ 30 is out of stock can I use this one instead? View answer

Answer posted 3 years ago

Question 16

Hello, I'd like to connect a CORE35 onto 1.5 inch pvc pipe. Do I need the 1.5" reducer ? Just want to double check. Thanks, Dave View answer

Answer posted 3 years ago

Question 17

16x32 x 5what size system do I need View answer

Answer posted 3 years ago

Question 18

I have the RJ+45 cell with the 1.5" thread. will this one fit? View answer

Answer posted 3 years ago | CircuPool® Cleaning Stand for CircuPool RJ Plus, Universal, and Si Systems

Question 19

How can I clean the clear chamber, I unscrewed the collar but i can't get the device apart. Thanks. View answer

Answer posted 3 years ago

Question 20

Where do you install the cartridge-looking device... On the intake line or the outflow (back to the pool) line? View answer

Answer posted 3 years ago

Question 21

Is it really better to oversize? Looking at the Universal40 for a 20K size pool. Will the 25K be just as efficient? Does the electronic box have a timer or do I need to tie it into my pool timer? Runs 12 hours per day. Using 220v pump. Thank you. View answer

Answer posted 3 years ago

Question 22

Is this item returnable in case it doesn’t fit? And how soon could I get it? View answer

Answer posted 3 years ago | Replacement Cells > Aftermarket Replacement Cells <span>fitting Hayward® / Goldline®</span>

Question 23

What Cell setting should I program my box too when using the Si40 UL40 cell? View answer

Answer posted 3 years ago

Question 24

How long is the wait T cell t15 View answer

Answer posted 3 years ago

Question 25

Is the screen replaceable? I did not see in on the site. View answer

Answer posted 3 years ago

Question 26

We will be replacing our old Zodiac LM23 chlorinator. We have a Hayward variable speed pump. I think the pool is a bit over 15000 gallons. Which system would be best for us? View answer

Answer posted 3 years ago

Question 27

I have a 5 plus year old SI45 now. I have replaced the cell and now it is blowing the fuse on the main panel. I’m not sure what the cost is to replace the main board or if I should purchase this new unit. Thoughts? View answer

Answer posted 3 years ago

Question 28

When do you know it's time to replace an old system? I have a CircuPool Si Series , 8 yrs old this past March, (salt). Can it be replaced with this one? View answer

Answer posted 3 years ago

Question 29

When do you expect this item to be back in stock? View answer

Answer posted 3 years ago

Question 30

Does this kit come with a flow switch and is this flow switch from the Hayward compatible with this one View answer

Answer posted 3 years ago

Question 31

Is this system Hayward compatible? View answer

Answer posted 3 years ago

Question 32

Will the plumbing for the SJ20 classic fit with the new SJ series? View answer

Answer posted 3 years ago

Question 33

is it plug and play 120 volt input hook-up. is it all in one inside program box is there a transformer inside the panel? or do I need extural View answer

Answer posted 3 years ago

Question 34

What size do I go with? My pool is 18 by 36 inground with a 4 foot shallow end and 9 feet in deep end which is gradual. Why would I choose one system over another?? What are your recommendations? I do not currently have a salt system View answer

Answer posted 3 years ago

Question 35

The pump has written on it : This pump must be installed with a two, multi, or variable speed pump motor controller. The manual says nothing about this. Do I need something else to install this or is it already on the pump? Thanks View answer

Answer posted 3 years ago

Question 36

we have a pentair intelliflo that just blew up on us could we replace with this? View answer

Answer posted 3 years ago

Question 37

When would this ship? Thank you View answer

Answer posted 3 years ago

Question 38

What is the correct cleaning cap to use for an RJ45 cell? View answer

Answer posted 3 years ago

Question 39

Can I install the unit on the discharge of the filter housing? View answer

Answer posted 3 years ago

Question 40

How often does the electrolytic cell need to be replaced? View answer

Answer posted 3 years ago

Question 41

What is the life expectancy of these cells? View answer

Answer posted 3 years ago | Replacement Cells > RJ PLUS-Series Replacement Cells

Question 42

is this unit 220V or 115V View answer

Answer posted 3 years ago

Question 43

How much is it to ship to 11715? Blue point NY View answer

Answer posted 3 years ago

Question 44

What is the minimum required flow (in GPM) for the RJ60+ Flow Switch to close and enable the Salt Cell to generate Chlorine? View answer

Answer posted 3 years ago

Question 45

Will part number CORE-CLHS fit a CORE 35? View answer

Answer posted 3 years ago

Question 46

How can you predict the lifespan of the cell? View answer

Answer posted 3 years ago

Question 47

Hello, Will this work for a Jandy Aquapure replacement? View answer

Answer posted 3 years ago | CircuPool® Bypass Cell for RJ-PLUS and UL-Series Salt Systems

Question 48

What is the salt level on this system View answer

Answer posted 3 years ago

Question 49

3 questions, 1) is there any risk of CO2 added in the drain ports of the pump causing cavitation damage in the pump? 2) if installation complexity isn’t a problem, would you still recommend injecting at the drain ports? 3) I have 2 pumps, a “filter” pump that is the workhorse pushing water through filter, UV sanitizer, heater, wall returns, and when active floor cleaner jets. The other “water feature” pump runs at 1100 rpm 24/7 to overflow a zero edge spa. Which flow stream should I introduce CO2 to? View answer

Answer posted 3 years ago | Sanitation > pH Control

Question 50

Hi there, I have a Circupool Si 45 salt cell that has gone bad. Can I replace it with a Si 60 cell instead? Is the size the same for both? I have a 36,000 gallon pool in the Dallas area. Thanks, Anton View answer

Answer posted 3 years ago

Browse by Topic

Tools