CircuPool SJ-A Series Salt Chlorine Generators - Owner Resources Q&A

Question 1

The Flow LED on the panel will turn green for aprox. 10 seconds and then go red for aprox. 2 min. When it will go green again for 10 seconds repeating. Could this be a faulty flow switch or something else? View answer

Asked 3 ´years ago

Question 2

I have a SJ-series system 4 years ago. works great. I just had a variable speed pool pump installed. It goes threw its own internal timers. does the SJ- series have a built in flow switch sensor built in. Worried about the unit coming on via the old pool timer without the new pump running? View answer

Asked 6 ´years ago

Question 3

Hi, I'm a return customer. Well, I think it's time to replace the old system with a new one. My question is... I see a round "white" fitting with wires attached in your photos. What is that? I don't have anything like that on my current system (RJ20 serial # 030282). Also, will the chlorinator fit the same fittings as my old system? Thank You! View answer

Asked 4 ´years ago

Question 4

When its generating how do you know its producing View answer

Asked 5 ´years ago

Question 5

Only number two polarity comes on View answer

Asked 5 ´years ago

Question 6

How can you tell if your salt cell is, View answer

Asked 1 ´year ago

Question 7

Will the flow switch operate properly in the vertical down position View answer

Asked 1 ´year ago

Question 8

I have an SJ-35 with 5 vanes, but only 2 of them are generating bubbles. Is that normal, or is there a problem? View answer

Asked 1 ´year ago

Question 9

I have a ret water temp light and a red flow light. Its 80 degrees out and the system was working yesterday View answer

Asked 3 ´months ago

Question 10

I am having issues temp and flow lights are on . Purchased system last summer

Asked 2 ´months ago

Question 11

My SJ series salt system has low flow light and low temp light on. Replaced the low flow sensor and still have both

Asked 1 ´month ago

Question 12

How do I clean the salt generator View answer

Asked 1 ´month ago

Question 13

Will an SJ-35 cell work in an SJ-30 system? View answer

Asked 1 ´year ago

Question 14

flow light wont turn green View answer

Asked 1 ´year ago

Question 15

Where is the serial number located? View answer

Asked 1 ´year ago

Question 16

My SJ20 is turning itself off and both the cell light and the sale light are showing red. The salt level is good. View answer

Asked 11 ´months ago

Question 17

Flow Switch Question View answer

Asked 1 ´year ago

Question 18

When adding the flow switch how far from the filter to switch and from switch to cell View answer

Asked 11 ´months ago

Question 19

I need to replace my SGS breeze, 320 controller and cell. can I use the sj20 w/o having to redue plumbing.

Asked 4 ´months ago

Question 20

I need 2 of theplastic blue divider spacers for the electrolytic cell View answer

Asked 2 ´months ago

Question 21

PVC T fitting replacement part for sj35a View answer

Asked 2 ´months ago

Question 22

SJ45 system Flow indicator - Green LED on for ~5sec, then RED for ~10sec, then back to Green for 5sec. etc, ?? View answer

Asked 2 ´months ago

Question 23

salt and cell light do not illuminate neither red or green?

Asked 2 ´months ago

Question 24

How do you change it from 110 volt to 220 volt?

Asked 1 ´month ago

Question 25

The Low Water Temp LED is red but water temp is 70 degrees and the Flow LED is red but it is definitely pumping. View answer

Asked 2 ´years ago

Question 26

all the lights are green but the generating light never turns on. I replaced the salt cell and still it won’t turn View answer

Asked 1 ´month ago

Question 27

Is it OK to install the salt generator cell (SJ-20) and flow sensor on the discharge piping of my pool cartridge cannister? View answer

Asked 4 ´years ago

Question 28

How difficult is it to convert a chlorine tablet system to the Circupool SJ~20 system? Is the conversion similar to the one you use to convert from one salt system to the circupool product. Thanks View answer

Asked 4 ´years ago

Question 29

How should the SJ-A Control Module unit be wired? View answer

Asked 3 ´years ago

Question 30

I soaked the cell in the muratic acid solution for 10’ but there are still mineral deposits visible on both ends View answer

Asked 2 ´years ago

Question 31

On our second SJ40 and have never used Super CL Mode and would like to know should the light be red.?? We just had the pool redone and need to get the chlorine and salinity back up to where they need to be.......... View answer

Asked 6 ´years ago

Question 32

How many amps does my CircuPool SJ pull? View answer

Asked 5 ´years ago

Question 33

Just started recently, when the unit first turns on, it hums and vibrates. View answer

Asked 2 ´years ago

Question 34

I bought a house with a 26qft pool. I'm trying to learn to control the salt chlorinator (SJ series) for my pool. The water is murky now, with algae. All parameters are ok (I check regularly), except chlorine and free chlorine levels, which are at 0. How do I know that the cell actually works? Is there a documentation regarding the controller? the left bottom green light has been blinking. Also, how is this controller related to the pump? I have Hayward controller for the pump, and I'm clueless here too. Please help. View answer

Asked 4 ´years ago

Question 35

What's the ideal system setting for SJ Series Salt System? View answer

Asked 3 ´years ago | Support

Question 36

flow led changing red to green; 6 seconds green - 8 seconds red - then green again View answer

Asked 2 ´years ago

CircuPool SJ-A Series Salt Chlorine Generators - Owner Resources Q&A

Activity timeframe

View More Product Details

Related Product

Browse by Topic

Tools