CircuPool SJ-A Series Salt Chlorine GeneratorsOwner Resources Questions & Answers

To prolong the life of a salt water chlorine generator's cell, would it be better to run the pool system at 25% for 24 hrs., 50% for 12 hrs. or 100% 6 hrs View answer

Asked 1 ´month ago

Where can I find the CircuPool serial number on my equipment?? View answer

Asked 2 ´years ago

SJ unit not working

Asked 1 ´month ago

Need flow switch assyembley View answer

Asked 1 ´month ago

Does flow sensor replace the need for a timer / programable time switch? View answer

Asked 1 ´month ago

How often is my salt cell supposed to be cleaned? View answer

Asked 1 ´month ago

Maximum Salt Levels for SJ

Asked 1 ´month ago

You recommend NOT using dry acid to adjust pH. What do you recommend instead? View answer

Asked 1 ´year ago

Flow and low temperature LEDs both red View answer

Asked 1 ´year ago

Can't find replacement for flow switch View answer

Asked 1 ´year ago

SJ45 system Flow indicator - Green LED on for ~5sec, then RED for ~10sec, then back to Green for 5sec. etc, ?? View answer

Asked 3 ´months ago

I installed a replacement SJ-45 cell but I’m not getting a salt or cell status light after running View answer

Asked 1 ´month ago

Is it possible to bypass the flow switch because the system turns on when the pump starts? View answer

Asked 1 ´year ago

I have a ret water temp light and a red flow light. Its 80 degrees out and the system was working yesterday View answer

Asked 5 ´months ago

Do I need to register my new system and if so, where do I register it at? View answer

Asked 2 ´years ago

My pool pump runs all the time how do I wire in my SJA series View answer

Asked 2 ´years ago

On our second SJ40 and have never used Super CL Mode and would like to know should the light be red.?? We just had the pool redone and need to get the chlorine and salinity back up to where they need to be.......... View answer

Asked 7 ´years ago

I have an SJ-35 with 5 vanes, but only 2 of them are generating bubbles. Is that normal, or is there a problem? View answer

Asked 1 ´year ago

Will the flow switch operate properly in the vertical down position View answer

Asked 1 ´year ago

flow light wont turn green View answer

Asked 1 ´year ago

My SJ series salt system has low flow light and low temp light on. Replaced the low flow sensor and still have both

Asked 2 ´months ago

The plastic button control panel is cracking. Can this be replaced? View answer

Asked 1 ´year ago

How do I clean the salt generator View answer

Asked 2 ´months ago

SJ35A sn:05BABAB85SGE0033. rep chlorinator.

Asked 1 ´month ago

Flo and low temp light on

Asked 1 ´month ago

I have a SJ 55 and the unit popped the reset button when I reset it , it smells like burnt wires, all lights are on View answer

Asked 20 ´days ago

Water is leaking from the back of my CircuPool SJ Series cell generator, what should I check to stop the leak? View answers

Asked 10 ´days ago

I have an SJ45A System that won't generate chlorine. View answer

Asked 1 ´year ago

How do I clean the cells View answer

Asked 2 ´months ago

Can the flow switch be installed vertical position? View answer

Asked 1 ´year ago

Just bought the sj35 and don’t see anywhere in the instructions how long the two risers have to be. How long should they be? View answer

Asked 5 ´years ago

I have an older SJ classic system. Does the cell from the new SJ system fit my box? View answer

Asked 22 ´days ago

The Digital Control Panel of the SJ-40 has stopped working how can I fix it? View answer

Asked 6 ´years ago

How many amps does my CircuPool SJ pull? View answer

Asked 5 ´years ago

How to install sj45a to variable speed pump View answer

Asked 2 ´years ago

The Low Water Temp LED is red but water temp is 70 degrees and the Flow LED is red but it is definitely pumping. View answer

Asked 2 ´years ago

The Flow LED on the panel will turn green for aprox. 10 seconds and then go red for aprox. 2 min. When it will go green again for 10 seconds repeating. Could this be a faulty flow switch or something else? View answer

Asked 4 ´years ago

Red salt light View answer

Asked 2 ´years ago

my old cell housing is leaking so i need to replace it. i ordered a new one which has treaded connectors but the existing housing was glued to the PVC . What parts do I need to connect the new housing unit? I have a SJ View answer

Asked 5 ´years ago

What's the ideal system setting for SJ Series Salt System? View answer

Asked 3 ´years ago | Support

Chlorinator worked last year but this year works for a few minutes then red light for cell and salt lights up. View answer

Asked 1 ´year ago

When adding the flow switch how far from the filter to switch and from switch to cell View answer

Asked 1 ´year ago

On my CircuPool SJ - there is a small air pocket in corner of housing exposing a sliver of the cell. Unit generating and all lights good. Is this OK? View answer

Asked 5 ´days ago

I want to see if my sj20 is still under warranty.

Asked 3 ´months ago

How do you claim a warranty on my CircuPool equipment? View answer

Asked 3 ´years ago

I got a salt cell in February. I am adding salt twice a week and after about three days I start to see loose alg View answer

Asked 3 ´years ago

Leaking salt cell View answer

Asked 2 ´years ago

Where is the serial number located? View answer

Asked 2 ´years ago

Why is it showing red lights and not producing chlorine? View answer

Asked 1 ´year ago

Can I purchase electronic pieces that have burnt up in the control panel? View answer

Asked 1 ´year ago

CircuPool SJ-A Series Salt Chlorine Generators - Owner Resources Q&A

Activity timeframe

View More Product Details

Related Product

Browse by Topic

Tools