CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources Q&A

Question 1

New system installed how long should low salt light and cell maintenance stay on View answer

Asked 9 ´months ago

Question 2

No cell communication View answer

Asked 9 ´months ago

Question 3

Total life View answer

Asked 9 ´months ago

Question 4

Just got the unit, any difference using 240v or 120v in performance?, can I use 120v wifi switch to connect it? View answer

Asked 9 ´months ago

Question 5

7 month old system and no chlorine View answer

Asked 1 ´year ago

Question 6

Can I replace the face on my RJ series? The digital screen no longer works. View answer

Asked 1 ´year ago

Question 7

The “Cell Connection “ comes up on the display and nothing works View answer

Asked 1 ´year ago

Question 8

My RJ 45 unit the screen is showing me no amperage what could be the cause View answer

Asked 1 ´year ago

Question 9

Rj45+ has power, but not generating View answer

Asked 2 ´years ago

Question 10

Should the power cord from control box to timer be routed in conduit? View answer

Asked 1 ´year ago

Question 11

Display shows zero salinity and temp of 164 degrees. Cell was cleaned and no change. Appears to be generating cl View answer

Asked 1 ´year ago

Question 12

what are dimensions of control box. RJ-30 I want to mount it on the circuit breaker panel. View answer

Asked 2 ´years ago

Question 13

All, I received my RJ-30 generator in the winter of 2019, installed for last season, this season I have been fighting with algae growth, and I think it is due to a defective flow sensor, is there some way I can clean it, or otherwise troubleshoot it before I have to replace the whole thing? I touched the wire on it today, and it stopped flickering with no-flow, and started generating again, so I am sure this is the issue. Please let me know, Louise View answer

Asked 4 ´years ago

Question 14

I just purchased RJ60+ System. Is there a maximum flow limit that I shall not exceed for the Salt Cell.? Maximum flow, for example 85 GPM, for their Salt Cell. View answer

Asked 2 ´years ago

Question 15

Is there a place where i can get actual dimensions? Like a shop drawing. Ive already managed to rule out the CORE55 from rough dimensions given to another. I suspect this model will be a much more close call on fitting. View answer

Asked 4 ´years ago

Question 16

I just installed an RJ60+ in place of my Aquapure 1400. I was just wondering- on the unit, there is a “remote” indicator. What is this for? Are there ways to adjust the unit remotely, perhaps interfacing it with the Jandy system? Thanks. View answer

Asked 4 ´years ago

Question 17

Will the system say when it’s time to change the cell? View answer

Asked 5 ´years ago

Question 18

I just ordered an RJ-45+. Should I install a check valve after the heater? View answer

Asked 2 ´years ago

Question 19

We have a RJ 45 and a pool with just under 14,000 gal. Once Chem levels are achieved how much salt should need to be added to maintain them. It is an indoor pool. View answer

Asked 3 ´years ago

Question 20

What is the warranty? I don’t see any info here. View answer

Asked 3 ´years ago

Question 21

Does the control module have to be covered or is it waterproof? View answer

Asked 4 ´years ago

Question 22

How often do you have to replace the salt cells? I see no mention of longevity View answer

Asked 4 ´years ago

Question 23

We just cleaned our cell and now we are having issues with it communicating to the system. There is a code saying Cell Connection. We have inspected the all of the cables and everything look to be in good shape. We have powered it down several times and disconnected it several times as well yet we can not get the cell to communicate with the system, W”hat could be the cause of this code? View answer

Asked 4 ´years ago

Question 24

Why not sell the flow switch with the Tee? But you you show the sensor with the tee to sell the sensor. View answer

Asked 1 ´year ago

Question 25

I soaked the cell in the muratic acid solution for 10’ but there are still mineral deposits visible on both ends View answer

Asked 1 ´year ago

Question 26

Just received it, and so psyched to replace my 18 year old Aquarite, it looks great. Can I keep the old flow switch from that system that still works fine, or do I need to swap in the new one. Just looking for simplicity in the install. Thanks, View answer

Asked 4 ´years ago

Question 27

I have an RJ-45 that has been working fine for about 2 years but now indicated "Cell Connect". View answer

Asked 1 ´year ago

Question 28

Reading on unit says cell not match.. View answer

Asked 1 ´year ago

Question 29

Readout says "cell not match" also the system will not power off...none of the buttons work ...help. View answer

Asked 1 ´year ago

Question 30

control panel will not go higher than 50% View answer

Asked 1 ´year ago

Question 31

Recommended set up on rj45 plus on 22000 gallon pool. Variable speed pump. Pump run time and percentage setting. Thanks View answer

Asked 4 ´years ago

Question 32

What determins when your RJ+45 Series" goes into it's "REST Cycle"? View answer

Asked 5 ´years ago

Question 33

Installed the RJ-30 just before summer hit here in the Houston area on a ~15K gallon pool. Just want to know if having to run it at around 85-90% power is normal for the hot summer days on this size of pool. View answer

Asked 2 ´years ago

Question 34

High salt light is flashing and showing 4500 what should I do it shows it’s still generating View answer

Asked 1 ´year ago

Question 35

I have an RJ-30 Plus system. What is the effect of Cell Version setting on the Menu? Each numerical value also has a '+' and '-'. What does this do to the operation of the system? This is not mentioned anywhere in the manual. View answer

Asked 3 ´years ago

Question 36

I am getting ready to install this unit but may have to install it vertically. What, if anything, do I need to do to insure the system works properly? Thanks, Marty View answer

Asked 3 ´years ago

Question 37

My pool's pump is off with power to the RJ-30. is that OK? View answer

Asked 1 ´year ago

Question 38

What size breaker is needed for a RJ45 ? Can I tie the pump and rj45 together? The 3 hp circuit pump says to not View answer

Asked 1 ´year ago

Question 39

I cleaned my r 40 cell and it still reads cell maintenance View answer

Asked 1 ´year ago

Question 40

Just purchased RJ30. Was told it is a self cleaning unit utilizing revers polarity. How do I know when it is in cleaning mode? View answer

Asked 5 ´years ago

Question 41

I bough the RJ -30 system April 2016 and I would like to know if there is a way to tell if it is still putting out as much chlorine as it was designed to? View answer

Asked 6 ´years ago

Question 42

I have the Circupool RJ 16. It says salt level is 2800 and really is 3600, How do you calibrate the unit? View answer

Asked 4 ´years ago

Question 43

My CircuPool RJ PLUS salt chlorinator lights up and then turns back off. View answer

Asked 1 ´year ago

Question 44

Can the unit be installed vertically? View answer

Asked 1 ´year ago

Question 45

NO SALINITY READING WHEN BUTTON PUSHED ON RJ30 PLUS View answer

Asked 1 ´year ago

Question 46

I got a salt cell in February. I am adding salt twice a week and after about three days I start to see loose alg View answer

Asked 1 ´year ago

Question 47

Will this keypad fit my rj30 ? View answer

Asked 2 ´years ago

Question 48

Can the RJ30 system be installed at a 45 degree angle? View answer

Asked 1 ´year ago

Question 49

Temperature readings over 110. Replaced flow switch. Temp readings still over 110. What should I do? View answer

Asked 1 ´year ago

Question 50

Low salt light View answer

Asked 1 ´year ago

CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources Q&A

Activity timeframe

View More Product Details

Related Product

Browse by Topic

Tools