Ask a Question

Ask your question here...

Home
Login
Register

Search...

Sanitation > Salt Chlorinators > RJ PLUS Series >

CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources Q&A

Filter

Activity timeframe

Apply filters

Questions

Most Popular

Recently Asked

Recently Active

Displaying no power. 240v measured. View answer

Asked 3 ´months ago

Key pad not lite can only see high temp View answer

Asked 5 ´days ago

Can the electrical cord be wired to a 3 prong male plug to use an outlet instead of hard wiring to electrical box? View answer

Asked 3 ´months ago

Our rj 30 was purchased in 2012. It’s showing water fault and low salt but salt is ok

Asked 3 ´months ago

Yellow cell maintenance light View answer

Asked 2 ´years ago

High salt light is flashing and showing 4500 what should I do it shows it’s still generating View answer

Asked 3 ´years ago

Stops generating after a few hours of running. Turn it off and on and back to normal. View answer

Asked 2 ´years ago

7 month old system and no chlorine View answer

Asked 3 ´years ago

My RJ45 control module shows cell volts 12.2 cell Amps 0.00A, power is set at MAX. Salinity shows Average:0000 View answer

Asked 2 ´years ago

Flow switch View answer

Asked 2 ´years ago

how to register my product View answer

Asked 2 ´years ago

what are dimensions of control box. RJ-30 I want to mount it on the circuit breaker panel. View answer

Asked 3 ´years ago

Should the power cord from control box to timer be routed in conduit? View answer

Asked 3 ´years ago

What is the RJ+ cell unit's maximum pressure (PSI) rating? View answer

Asked 4 ´years ago

Why not sell the flow switch with the Tee? But you you show the sensor with the tee to sell the sensor. View answer

Asked 2 ´years ago

My screen is not working View answer

Asked 2 ´years ago

I just installed an RJ60+ in place of my Aquapure 1400. I was just wondering- on the unit, there is a “remote” indicator. What is this for? Are there ways to adjust the unit remotely, perhaps interfacing it with the Jandy system? Thanks. View answer

Asked 6 ´years ago

New system installed how long should low salt light and cell maintenance stay on View answer

Asked 2 ´years ago

We have a RJ 45 and a pool with just under 14,000 gal. Once Chem levels are achieved how much salt should need to be added to maintain them. It is an indoor pool. View answer

Asked 4 ´years ago

Reported Temperature is high. View answer

Asked 2 ´years ago

Just got the unit, any difference using 240v or 120v in performance?, can I use 120v wifi switch to connect it? View answer

Asked 2 ´years ago

Flow Switch light is flashing View answer

Asked 2 ´years ago

control panel will not go higher than 50% View answer

Asked 2 ´years ago

Do I need the flow switch? View answer

Asked 2 ´years ago

We just cleaned our cell and now we are having issues with it communicating to the system. There is a code saying Cell Connection. We have inspected the all of the cables and everything look to be in good shape. We have powered it down several times and disconnected it several times as well yet we can not get the cell to communicate with the system, W”hat could be the cause of this code? View answer

Asked 5 ´years ago

Is there a way to set run time limit? View answer

Asked 2 ´years ago

What determins when your RJ+45 Series" goes into it's "REST Cycle"? View answer

Asked 6 ´years ago

I have an RJ-30 Plus system. What is the effect of Cell Version setting on the Menu? Each numerical value also has a '+' and '-'. What does this do to the operation of the system? This is not mentioned anywhere in the manual. View answer

Asked 4 ´years ago

if set below 70% my generator stops generating. i shut off and turn on it starts generating then stops again View answer

Asked 2 ´years ago

Just purchased RJ30. Was told it is a self cleaning unit utilizing revers polarity. How do I know when it is in cleaning mode? View answer

Asked 7 ´years ago

My Low flow light is on, I cleaned the cell, and it’s still on. What’s next View answer

Asked 2 ´years ago

Temperature readings over 110. Replaced flow switch. Temp readings still over 110. What should I do? View answer

Asked 2 ´years ago

How to program the RJ-30 to turn on and off? Is there a way to program the system? View answer

Asked 2 ´years ago

I cleaned my r 40 cell and it still reads cell maintenance View answer

Asked 2 ´years ago

Question about the Voltage View answer

Asked 2 ´years ago

RJ 30 Plus installed on 6/8/24 for a 10400 gal pool on startup with 0ppm salt. As of 6/10 salt reading is 4700ppm ? View answer

Asked 2 ´years ago

Can the unit be installed vertically? View answer

Asked 2 ´years ago

Does the Cell maintenance light stay on when first installed and how long will it stay on?? View answer

Asked 2 ´years ago

Salt cell is clogged within a week View answer

Asked 1 ´year ago

Noticed lots of calcium all over my pool what can I do to eliminate this View answer

Asked 1 ´year ago

My salt cell is creating foam in my pool View answer

Asked 2 ´years ago

I am receiving a "cell connection" message on View answer

Asked 1 ´year ago

On start up all lights are on

Asked 1 ´month ago

The water temp in the pool is 86 degrees and the temp high shown on the power unit is 160F. This is not possible. W View answer

Asked 1 ´year ago

On my RJ+30 in the window it is saying high heat and the chlorine light flickers. What can I look for to fix? View answer

Asked 1 ´year ago

The fuse blows very soon after replacing View answer

Asked 1 ´year ago

What is the Warranty on an RJ45 View answer

Asked 1 ´year ago

No power View answer

Asked 1 ´year ago

We just bought our house and the panel won’t turn on at all. View answer

Asked 2 ´years ago

Message box says cell connection. No buttons work View answer

Asked 2 ´years ago

Show: Select how many pieces of content to show

View More Product Details

CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources

Learn how to get the most out of your RJ-Series Salt System

View Details

Related Product

CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources

Learn how to get the most out of your RJ-Series Salt System

View Details

Browse by Topic

Sales
Sales
Support
Support
Other
Other

Tools

Help

Search...

Home | Terms & Conditions | Help

Please wait...