CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources Q&A

Question 1

Asked 7 ´months ago

Question 2

The power light is lit and the display says, “Cell connection” but the green generator light is not lit. View answer

Asked 7 ´months ago

Question 3

Why do I have to clean my unit every week? My pool chemicals are all in range and I check them twice a week. View answer

Asked 7 ´months ago

Question 4

I purchased this system 2 yrs ago. My pump is not working and showing an E-09 error. Can you please help. Thanks. View answer

Asked 7 ´months ago

Question 5

Total life View answer

Asked 7 ´months ago

Question 6

Flow Switch light is flashing View answer

Asked 7 ´months ago

Question 7

Just got the unit, any difference using 240v or 120v in performance?, can I use 120v wifi switch to connect it? View answer

Asked 7 ´months ago

Question 8

No cell communication View answer

Asked 8 ´months ago

Question 9

New system installed how long should low salt light and cell maintenance stay on View answer

Asked 8 ´months ago

Question 10

Need a temperature flow switch View answer

Asked 8 ´months ago

Question 11

I keep getting cell connection error on my system. Any suggestions? View answer

Asked 8 ´months ago

Question 12

I divert water to my deck jets and pool slide. Does it hurt the system to have the pump on & no water going to salt View answer

Asked 8 ´months ago

Question 13

no power on unit View answer

Asked 8 ´months ago

Question 14

When running my RJ60 at any power setting I am getting very much white crystal looking debris from my return nozzle View answer

Asked 8 ´months ago

Question 15

how to register my product View answer

Asked 8 ´months ago

Question 16

Hi Why my Salt System Panel says Cell Not Match, Thanks in advance View answer

Asked 8 ´months ago

Question 17

Do I need the flow switch? View answer

Asked 9 ´months ago

Question 18

if set below 70% my generator stops generating. i shut off and turn on it starts generating then stops again View answer

Asked 9 ´months ago

Question 19

When you install the 2 jumpers to break the unit down to 120v, do the white wires stay on with jumpers? View answer

Asked 9 ´months ago

Question 20

Do I need to register View answer

Asked 9 ´months ago

Question 21

Generating stuck on 50% will not adjust View answer

Asked 9 ´months ago

Question 22

Screen is frozen with "cell connection " error message. It won't turn off by pushing the button. Warranty coverage? View answer

Asked 9 ´months ago

Question 23

Cell Connection Message View answer

Asked 9 ´months ago

Question 24

Does the Cell maintenance light stay on when first installed and how long will it stay on?? View answer

Asked 9 ´months ago

Question 25

RJ 30 Plus installed on 6/8/24 for a 10400 gal pool on startup with 0ppm salt. As of 6/10 salt reading is 4700ppm ? View answer

Asked 9 ´months ago

Question 26

No cell connection won’t turn off View answer

Asked 9 ´months ago

Question 27

cell connection message and control panel will not power off with power button View answer

Asked 9 ´months ago

Question 28

RJ-60 Plus does the direction of flow through the cell matter? View answer

Asked 1 ´year ago | Support

Question 29

Should the power cord from control box to timer be routed in conduit? View answer

Asked 1 ´year ago

Question 30

7 month old system and no chlorine View answer

Asked 1 ´year ago

Question 31

I got a salt cell in February. I am adding salt twice a week and after about three days I start to see loose alg View answer

Asked 1 ´year ago

Question 32

Power level readings View answer

Asked 1 ´year ago | Support

Question 33

Rj45+ has power, but not generating View answer

Asked 1 ´year ago

Question 34

what are dimensions of control box. RJ-30 I want to mount it on the circuit breaker panel. View answer

Asked 2 ´years ago

Question 35

All, I received my RJ-30 generator in the winter of 2019, installed for last season, this season I have been fighting with algae growth, and I think it is due to a defective flow sensor, is there some way I can clean it, or otherwise troubleshoot it before I have to replace the whole thing? I touched the wire on it today, and it stopped flickering with no-flow, and started generating again, so I am sure this is the issue. Please let me know, Louise View answer

Asked 4 ´years ago

Question 36

How do I shock my salt water pool that has a RJ60+ system. View answer

Asked 2 ´years ago

Question 37

High salt light is flashing and showing 4500 what should I do it shows it’s still generating View answer

Asked 1 ´year ago

Question 38

I just purchased RJ60+ System. Is there a maximum flow limit that I shall not exceed for the Salt Cell.? Maximum flow, for example 85 GPM, for their Salt Cell. View answer

Asked 2 ´years ago

Question 39

Hello. I have an RJ-60+ which is rated at 300W, so presumably it only draws 1.36A at 220V. However, the manual also mentions the cell current ranging between 2.5 and 7.8 amps. I can also see the cell current displayed when I cycle through the menu options. For example, at 50%, it shows 5.7 amps. I'm assuming this cell current is different from the load on the circuit breaker. Can you confirm please? View answer

Asked 3 ´years ago

Question 40

Hello, I have just purchased the RJ-30 Plus Salt system, and wanted to know it's power usage in Watts and Amps. Also, is it more efficient to connect it to 220v vs. 120v, and if so, how much more efficient? Whats the amperage & wattage for 220v vs. 120v connections? Thank you! View answer

Asked 3 ´years ago

Question 41

Display shows zero salinity and temp of 164 degrees. Cell was cleaned and no change. Appears to be generating cl View answer

Asked 1 ´year ago

Question 42

Is there a place where i can get actual dimensions? Like a shop drawing. Ive already managed to rule out the CORE55 from rough dimensions given to another. I suspect this model will be a much more close call on fitting. View answer

Asked 4 ´years ago

Question 43

The “Cell Connection “ comes up on the display and nothing works View answer

Asked 1 ´year ago

Question 44

I just installed an RJ60+ in place of my Aquapure 1400. I was just wondering- on the unit, there is a “remote” indicator. What is this for? Are there ways to adjust the unit remotely, perhaps interfacing it with the Jandy system? Thanks. View answer

Asked 4 ´years ago

Question 45

Will the system say when it’s time to change the cell? View answer

Asked 4 ´years ago

Question 46

What should my amps read View answer

Asked 1 ´year ago

Question 47

Can I replace the face on my RJ series? The digital screen no longer works. View answer

Asked 1 ´year ago

Question 48

I just ordered an RJ-45+. Should I install a check valve after the heater? View answer

Asked 2 ´years ago

Question 49

Cell Connection message. I have done everything in the trouble shooting area in the manual. View answer

Asked 1 ´year ago

Question 50

I own this system but it sometimes does not produce enough chlorine for my 240 00 gallon pool, guess to runtime being less than 24 hours. can i upgrade to RJ 60 salt cell without changing controller? will controller recognize larger cell and correctly produce chlorine? View answer

Asked 3 ´years ago

CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources Q&A

Activity timeframe

View More Product Details

Related Product

Browse by Topic

Tools