CircuPool EDGE Series Salt Chlorine GeneratorsOwner Resources Questions & Answers

How do you claim a warranty on my CircuPool equipment? View answer

Asked 3 ´years ago

the salt table indicates i need to add 876# of salt on new water. View answer

Asked 1 ´year ago

Where can I find the CircuPool serial number on my equipment?? View answer

Asked 2 ´years ago

My low salt light is flashing but I measure salt level in the pool at 4000ppm View answer

Asked 7 ´months ago

System error View answer

Asked 4 ´months ago

Check cell light is on View answer

Asked 2 ´years ago

the control panel has no power and not indicator lights View answer

Asked 4 ´months ago

Why hasTemp sensor malfunction after 22hrs running from new install? View answer

Asked 4 ´months ago

sacrificial anode / cyanuric acid stabilizer level in pool? View answer

Asked 3 ´years ago

I want to replace my PureChlor generator with a CircuPool Edge 25. I would like to know the length of the cell, View answer

Asked 1 ´year ago

Can the flow switch be installed upstream of the heater? View answer

Asked 1 ´year ago

How long is the salt generator supposed to last? I just recently cleaned mine as instructed reinstalled and it stop View answer

Asked 2 ´years ago

how to determine if edge 40 cell needs replacement View answer

Asked 2 ´years ago

What is the warranty on the chlorine generator View answer

Asked 1 ´year ago

I have a three year old Edge system and it has started leaking from the input side of the connection. View answer

Asked 4 ´months ago

Cell light stays steady on

Asked 3 ´months ago

Do I need to register my new system and if so, where do I register it at? View answer

Asked 2 ´years ago

I got a salt cell in February. I am adding salt twice a week and after about three days I start to see loose alg View answer

Asked 3 ´years ago

Can the flow switch be installed horizontally and the cell be installed vertically? View answer

Asked 3 ´months ago

What's the ideal system setting for EDGE Series Salt System? View answer

Asked 3 ´years ago | Support

My salt generator has power but no indicator lights. Circupool Edge. View answer

Asked 2 ´months ago

Installed last weekend edge new units system error light tested 3 lights temp sensor reset back after 22 hrs. View answer

Asked 4 ´months ago

panel dose not turn when i start time

Asked 2 ´months ago

Edge series blank for winter use

Asked 2 ´months ago

I bought an Edge 25 from Discount Salt Pool, is that product covered under warranty or do I have to order from you to receive a full warranty? View answer

Asked 2 ´years ago

register my device

Asked 2 ´years ago

Can the cell and flow switch be mounted on an angle?

Asked 2 ´months ago

Am I able to bond the Edge system with my pool? I don’t see anywhere to connect the bonding wire? View answer

Asked 2 ´years ago

Low Salt light blinking on my CircuPool Edge 25. It was installed 1 month ago, test strips and tester read 3900, and the pool temp is 82. View answer

Asked 2 ´years ago

My control panel got moisture in it due to high humidity and condensation. Is that covered under the warrantee? View answer

Asked 12 ´months ago

system error 5 & 6

Asked 1 ´month ago

Circuit Breaker? View answer

Asked 2 ´years ago

Water flow light is on, not producing chlorine View answer

Asked 1 ´year ago

Is the 6"-12" of straight pipe absolutely necessary before entering the flow sensor? View answer

Asked 1 ´year ago

My troubleshooting process ended with 7 blue LEDs showing which says that control module replacement is needed View answer

Asked 1 ´year ago

I just bought a new Edge40 and it keeps saying check cell View answer

Asked 1 ´year ago

My CircuPool Edge unit is producing too much Chlorine at the lowest setting, and will sometimes introduce bubbles? View answer

Asked 1 ´year ago

How many titanium plates does this EDGE-40 cell have? View answer

Asked 3 ´years ago

how long are the cables for the cell and flow switch for the edge system View answer

Asked 2 ´months ago

Orientation of cell View answer

Asked 2 ´months ago

I have a Circupool Edge model 40. The check cell light is on. I turned the unit on a couple days ago. View answer

Asked 2 ´months ago

I set everything up and I cannot get any lights to come on

Asked 1 ´month ago

Does this model work with 220V? View answer

Asked 10 ´months ago

I have an edge system with 3.5” O.D. Threads. What is the P/N for the correct stand to support cell during cleani

Asked 1 ´month ago

Check cell comes on even after cell has been cleaned, 3 years old View answer

Asked 1 ´year ago

Not turning on View answer

Asked 1 ´year ago

Maximum input voltage View answer

Asked 1 ´year ago

system error 5 & 6

Asked 1 ´month ago

temperature sensor

Asked 1 ´month ago

I have a problem with controller not working . I have called many times but cannot get to a person. what do I do? View answer

Asked 14 ´days ago

CircuPool EDGE Series Salt Chlorine Generators - Owner Resources Q&A

Activity timeframe

View More Product Details

Related Product

Browse by Topic

Tools