CircuPool SJ-A Series Salt Chlorine GeneratorsOwner Resources Questions & Answers

What does a blinking red salt light mean on my SJ-45A unit? Cell light is green. Salinity levels are correct. View answer

Asked 1 ´year ago

I am having issues temp and flow lights are on . Purchased system last summer

Asked 25 ´days ago

Can't find replacement for flow switch View answer

Asked 1 ´year ago

Where can I find the CircuPool serial number on my equipment?? View answer

Asked 2 ´years ago

How do you claim a warranty on my CircuPool equipment? View answer

Asked 3 ´years ago

Where is the serial number located? View answer

Asked 1 ´year ago

Can the flow switch be installed vertical position? View answer

Asked 1 ´year ago

Can I purchase electronic pieces that have burnt up in the control panel? View answer

Asked 1 ´year ago

You recommend NOT using dry acid to adjust pH. What do you recommend instead? View answer

Asked 1 ´year ago

sacrificial anode / cyanuric acid stabilizer level in pool? View answer

Asked 2 ´years ago

Checking on an order from yesterday. Never got a confirmation. It was a flow sensor for a SJ series View answer

Asked 7 ´days ago

Flow and low temperature LEDs both red View answer

Asked 1 ´year ago

Can the flow switch be installed upstream of the heater? View answer

Asked 1 ´year ago

Is it possible to bypass the flow switch because the system turns on when the pump starts? View answer

Asked 1 ´year ago

Does the salt go directly into the pool on a new pool start up View answer

Asked 2 ´years ago

How to install sj45a to variable speed pump View answer

Asked 2 ´years ago

The Low Water Temp LED is red but water temp is 70 degrees and the Flow LED is red but it is definitely pumping. View answer

Asked 2 ´years ago

Red salt light View answer

Asked 2 ´years ago

I soaked the cell in the muratic acid solution for 10’ but there are still mineral deposits visible on both ends View answer

Asked 2 ´years ago

Do I need to register my new system and if so, where do I register it at? View answer

Asked 2 ´years ago

How do I buy a replacement for the SJ 3500 Generator buy it's self?? View answer

Asked 3 ´years ago

all the lights are green but the generating light never turns on. I replaced the salt cell and still it won’t turn View answer

Asked 3 ´days ago

My flow & low temp red lights come on immediately & neither is an issue. What needs checked or replaced ? View answer

Asked 2 ´months ago

Will the flow switch operate properly in the vertical down position View answer

Asked 10 ´months ago

Flow Switch Question View answer

Asked 1 ´year ago

I have the SJ 20 system can i replace the salt cell with a SJ 35 cell or are the control panels different? View answer

Asked 2 ´years ago

Flow switch led red when water is flowing? View answer

Asked 2 ´years ago

salt and cell light do not illuminate neither red or green?

Asked 20 ´days ago

I have a ret water temp light and a red flow light. Its 80 degrees out and the system was working yesterday View answer

Asked 2 ´months ago

Chlorinator worked last year but this year works for a few minutes then red light for cell and salt lights up. View answer

Asked 1 ´year ago

Why does my CircuPool SJ-20 Salt Chlorine Generator show low water temp and flow red lights even after replacing the flow sensor? View answer

Asked 1 ´year ago

I dont have any lights coming on anymore, does that mean my unit is bad on my SJ 45A? View answer

Asked 1 ´year ago

SJ series chlorinator is not producing chlorine View answer

Asked 2 ´years ago

flow led changing red to green; 6 seconds green - 8 seconds red - then green again View answer

Asked 2 ´years ago

I just bought one of these to replace my origional SJ-55 Housing that does not have the xxxx on adapters to connect to the return line. Is there an O-Ring that goes between the adapter and the Clear Housing to insure a complete seal? View answer

Asked 4 ´years ago

The Flow LED on the panel will turn green for aprox. 10 seconds and then go red for aprox. 2 min. When it will go green again for 10 seconds repeating. Could this be a faulty flow switch or something else? View answer

Asked 3 ´years ago

why does the housing leak? I replaced gasket and it leaks around the threads View answer

Asked 3 ´years ago

Just bought the sj35 and don’t see anywhere in the instructions how long the two risers have to be. How long should they be? View answer

Asked 5 ´years ago

Is it OK to install the salt generator cell (SJ-20) and flow sensor on the discharge piping of my pool cartridge cannister? View answer

Asked 4 ´years ago

Can the unit be mounted on its side rather than upright (the intake and output openings upward)? View answer

Asked 5 ´years ago

How many amps does my CircuPool SJ pull? View answer

Asked 4 ´years ago

Why is it showing red lights and not producing chlorine? View answer

Asked 1 ´year ago

I have a SJ-series system 4 years ago. works great. I just had a variable speed pool pump installed. It goes threw its own internal timers. does the SJ- series have a built in flow switch sensor built in. Worried about the unit coming on via the old pool timer without the new pump running? View answer

Asked 6 ´years ago

Do you have to use the flow switch on the SJ-20A ? View answer

Asked 1 ´year ago

My SJ series salt system has low flow light and low temp light on. Replaced the low flow sensor and still have both

Asked 4 ´days ago

How do you change it from 110 volt to 220 volt?

Asked 5 ´days ago

Will an SJ-35 cell work in an SJ-30 system? View answer

Asked 11 ´months ago

How can you tell if your salt cell is, View answer

Asked 11 ´months ago

No lights on the panel View answer

Asked 1 ´year ago

How should the SJ-A Control Module unit be wired? View answer

Asked 3 ´years ago

CircuPool SJ-A Series Salt Chlorine Generators - Owner Resources Q&A

Activity timeframe

View More Product Details

Related Product

Browse by Topic

Tools