Salt Chlorinators Q&A

Question 1

I own this system but it sometimes does not produce enough chlorine for my 240 00 gallon pool, guess to runtime being less than 24 hours. can i upgrade to RJ 60 salt cell without changing controller? will controller recognize larger cell and correctly produce chlorine? View answer

Asked 3 ´years ago

Question 2

I just ordered an RJ-45+. Should I install a check valve after the heater? View answer

Asked 2 ´years ago

Question 3

Can this replace a Jandy Aquapure 1400 with automation (Jandy AquaLink)? View answer

Asked 5 ´years ago

Question 4

max amperage draw at 220v View answer

Asked 4 ´years ago

Question 5

Does this generator cell plug up with calcite quicker/more readily than the CORE? We have very hard water and very high temperatures, View answer

Asked 4 ´years ago

Question 6

Will the system say when it’s time to change the cell? View answer

Asked 4 ´years ago

Question 7

I just installed an RJ60+ in place of my Aquapure 1400. I was just wondering- on the unit, there is a “remote” indicator. What is this for? Are there ways to adjust the unit remotely, perhaps interfacing it with the Jandy system? Thanks. View answer

Asked 4 ´years ago

Question 8

Is there a place where i can get actual dimensions? Like a shop drawing. Ive already managed to rule out the CORE55 from rough dimensions given to another. I suspect this model will be a much more close call on fitting. View answer

Asked 4 ´years ago

Question 9

Hello, I have just purchased the RJ-30 Plus Salt system, and wanted to know it's power usage in Watts and Amps. Also, is it more efficient to connect it to 220v vs. 120v, and if so, how much more efficient? Whats the amperage & wattage for 220v vs. 120v connections? Thank you! View answer

Asked 3 ´years ago

Question 10

Hello. I have an RJ-60+ which is rated at 300W, so presumably it only draws 1.36A at 220V. However, the manual also mentions the cell current ranging between 2.5 and 7.8 amps. I can also see the cell current displayed when I cycle through the menu options. For example, at 50%, it shows 5.7 amps. I'm assuming this cell current is different from the load on the circuit breaker. Can you confirm please? View answer

Asked 3 ´years ago

Question 11

What is the RJ+ cell unit's maximum pressure (PSI) rating? View answer

Asked 2 ´years ago

Question 12

How do I shock my salt water pool that has a RJ60+ system. View answer

Asked 2 ´years ago

Question 13

Will this work with my existing T-15 cell? View answer

Asked 5 ´years ago

Question 14

Can the universal system be used to replace a traditional chlorine pool? What is the difference between this and the RJ system? View answer

Asked 4 ´years ago

Question 15

Will this be a direct replacement for the Si45? View answer

Asked 4 ´years ago

Question 16

I have an auto clear system will this this work to replace that system. Thanks Scott View answer

Asked 3 ´years ago

Question 17

Does this product eliminate the need for chlorine By generating it’s own salt ? View answer

Asked 3 ´years ago

Question 18

Is the cell a direct replacement for the Pentair IC20? And, is the flowmeter integral it the cell? View answer

Asked 3 ´years ago

Question 19

I currently have a Jandy AquaPure PLC1400 that went bad. Can this replace that without professional? Thanks much. Duane View answer

Asked 3 ´years ago

Question 20

How effective is this systm View answer

Asked 3 ´years ago

Question 21

Can i purchase just the control module for a CircuPool Universal Series / SI Series unit? View answer

Asked 2 ´years ago

Question 22

Are there any specific instructions for storing in the winter months? Covering? (for CircuPool Universal Series salt chlorinator) View answer

Asked 2 ´years ago

Question 23

Will this keypad fit my rj30 ? View answer

Asked 2 ´years ago

Question 24

I have space restrictions. Would you please send me a drawing with dimensions for the Core 55? View answer

Asked 2 ´years ago

Question 25

With a variable speed pump is it ok to leave the generator powered all the time even when the pump shuts off View answer

Asked 2 ´years ago

Question 26

Is this a complete system? How easy is this to install? View answer

Asked 5 ´years ago

Question 27

Can this be used on an above ground pool? View answer

Asked 5 ´years ago

Question 28

IS THIS A 110V UNIT ? View answer

Asked 4 ´years ago

Question 29

need more infro on the system View answer

Asked 3 ´years ago

Question 30

Hi, Can I use this with my existing pool pump? Do you have it in stock? View answer

Asked 3 ´years ago

Question 31

When will SJ-20 system be available? View answer

Asked 3 ´years ago

Question 32

What is the optimum Salt content for this unit. I think its referred to as Parts per million (PPM) Thank You View answer

Asked 3 ´years ago

Question 33

can it connect to a smart phone? View answer

Asked 3 ´years ago

Question 34

Is the SJ20 110 or 240 volt? View answer

Asked 3 ´years ago

Question 35

When will these be back in stock? View answer

Asked 3 ´years ago

Question 36

Is it OK to install the salt generator cell (SJ-20) and flow sensor on the discharge piping of my pool cartridge cannister? View answer

Asked 2 ´years ago

Question 37

Do I need a flow sensor with the SJ system? How do you know the differences between SJ-20 and others? Is it size of pool? Location? View answer

Asked 2 ´years ago

Question 38

Will this handle a 72000 litre pool in a northern rn climate View answer

Asked 2 ´years ago

Question 39

Only number two polarity comes on View answer

Asked 4 ´years ago

Question 40

When its generating how do you know its producing View answer

Asked 3 ´years ago

Question 41

Hi, I'm a return customer. Well, I think it's time to replace the old system with a new one. My question is... I see a round "white" fitting with wires attached in your photos. What is that? I don't have anything like that on my current system (RJ20 serial # 030282). Also, will the chlorinator fit the same fittings as my old system? Thank You! View answer

Asked 2 ´years ago

Question 42

Is this compatible for a compupool inlet and outlet hook ups? View answer

Asked 5 ´years ago

Question 43

I have a SJ-series system 4 years ago. works great. I just had a variable speed pool pump installed. It goes threw its own internal timers. does the SJ- series have a built in flow switch sensor built in. Worried about the unit coming on via the old pool timer without the new pump running? View answer

Asked 5 ´years ago

Question 44

Does it only work when pump running and does it have a chlorine level reading View answer

Asked 3 ´years ago

Question 45

How easy are is the SJ 35 to clean and how often does it need clening. View answer

Asked 3 ´years ago

Question 46

I have a 15,000 gallon pool with a 3 year old waves/breeze unit that needs to be replaced. Just will not generate chlorine since install. Will this unit provide the correct chlorine and sanitizer needed for this size pool View answer

Asked 3 ´years ago

Question 47

Any estimate on when the SJ-35 will be back in stock? View answer

Asked 3 ´years ago

Question 48

How long is the cord that connects the cell housing to the control module? View answer

Asked 3 ´years ago

Question 49

Will the plumbing for the SJ20 classic fit with the new SJ series? View answer

Asked 2 ´years ago

Question 50

Just bought the sj35 and don’t see anywhere in the instructions how long the two risers have to be. How long should they be? View answer

Asked 3 ´years ago

Salt Chlorinators Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic

Tools