Question 1

Can I use universal 25 chlorinator on above ground pool View answer

Asked 1 ´year ago

Question 2

where can i get a replacement keypad for the JS series unit? View answer

Asked 5 ´years ago

Question 3

The keypad is showing output-off when I reset by pressing the + key and bring it up to 60 or 80, but in a few minutes or couple hours is back on output-off, Do I need a new keypad or a new circuit board? thank you View answer

Asked 5 ´years ago

Question 4

I have a rj 45 classic the it had on panel.power off and will not turn on will the key pad help this or do u need a whole new control panel View answer

Asked 4 ´years ago

Question 5

Is the screen replaceable? I did not see in on the site. View answer

Asked 3 ´years ago

Question 6

Is there a replacement cable for the RJ series which connects the controller to the cell? I believe my blue connector has failed. View answer

Asked 6 ´years ago

Question 7

Hello, the Replacement Union looks like the part I need but I'm unsure. I do have a classic RJ system. The part I need fills the open end of the clear cylinder. It also hold the electrodes. I also need the bolts and male electrodes, and the rubber o ring. I would also like to buy a replacement electrical cord with the female red, black, and blue connectors attached. Could you please supply part number so I can order?Thank you, Rih Kosina View answer

Asked 6 ´years ago

Question 8

Is this the right 2" union for a RJ +? View answer

Asked 5 ´years ago

Question 9

Temperature readings over 110. Replaced flow switch. Temp readings still over 110. What should I do? View answer

Asked 1 ´year ago | Sanitation > Salt Chlorinators > RJ PLUS Series > CircuPool RJ-PLUS Series Salt Chlorine Generators - Owner Resources

Question 10

Is this a set or do I need to order 2? View answer

Asked 5 ´years ago

Question 11

Is this the correct 2" cell union for a RJ30+ system? View answer

Asked 4 ´years ago

Question 12

Looking for replacement unions and O-rings for RJ-45+ What is the part number? View answer

Asked 4 ´years ago

Question 13

does this come as one or both pieces View answer

Asked 4 ´years ago

Question 14

I have a rjjc+30, sn 05a75da4d1850010, I need a replacement union, I do not know if it is a 3rd generation or not. Please advise. Thanks, Mark Goodrich View answer

Asked 4 ´years ago

Question 15

I am reinstalling my RJ60+ because of leaks. Is this union the same as the one that came with my RJ60+. Does it a a groove cut in it for the o-ring? View answer

Asked 3 ´years ago

Question 16

Does this fit RJ30? Also, where is it located and how do you remove old one? View answer

Asked 3 ´years ago

Question 17

Is the CircuPool® Replacement Union sold as a single piece or as a pair? View answer

Asked 4 ´years ago

Question 18

I have a Circupool Model Si30. I have the cell with the female part of the union the replacement did not come with the inside part that glues to the pipe. I need the adapters at 1-1/2". What item # would I need? View answer

Asked 3 ´years ago

Question 19

Is this the main board for the chlorine generator. View answer

Asked 4 ´years ago

Question 20

Is the circuit board for a CircuPool Universal Series??? View answer

Asked 4 ´years ago

Question 21

How hard is it to change the cell? I have an RJ 60plus. View answer

Asked 1 ´year ago

Question 22

I have an AquaRite Model: AQ-RITE-X295; SN 5A0710-1047242, rev 1.4. Can I replace the blown circuit board with your CircuPool Si PCB? View answer

Asked 3 ´years ago

Question 23

How to install sj45a to variable speed pump View answer

Asked 1 ´year ago | Sanitation > Salt Chlorinators > SJ Series > CircuPool SJ-A Series Salt Chlorine Generators - Owner Resources

Question 24

My current Si controller will not index when the button is pushed. Will this fix the problem or do I need the other board? View answer

Asked 3 ´years ago

Question 25

Chlorine is not being generated. New cell with about 6 months service. Will a problem with the small board not indexing causing this problem? View answer

Asked 3 ´years ago

Question 26

do you make a similar cap for the RJ+ (RJ60N) ? View answer

Asked 6 ´years ago

Question 27

Is there something like that for RJ classic? View answer

Asked 4 ´years ago

Question 28

Does this item come with an o-ring? View answer

Asked 4 ´years ago

Question 29

is this 2 pieces? View answer

Asked 3 ´years ago

Question 30

How do you get wire through the cap View answer

Asked 3 ´years ago

Question 31

Will the RJ45 plumbing interchange with my old circupool core View answer

Asked 1 ´year ago

Question 32

does it fit for sj40 series? View answer

Asked 4 ´years ago

Question 33

Does this fit all SJ series? If not, refundable? View answer

Asked 3 ´years ago

Question 34

Please can you provide a technical drawing for this. Looking to replace a Surechlor 3000 SC210 and need to compare sizes/threads/fittings etc. thanks in advance, Gary View answer

Asked 3 ´years ago

Question 35

does anyone know where this o ring should go ? View answer

Asked 6 ´years ago

Question 36

Is this the ORing that goes in the Union Nut to seal against the Face of the Generator? View answer

Asked 4 ´years ago

Question 37

Where does the print go on the winter cap. It seems to be placed on the top and outside of cap but it leaks. So should it be on the inside when installing View answer

Asked 4 ´years ago

Question 38

Does this 0-ring fit the electolytic cell for the CircuPool Core 35 unit? View answer

Asked 3 ´years ago

Question 39

Is this the 3 wire plug that connects to the sj controller? View answer

Asked 4 ´years ago

Question 40

Any idea when this will be back in stock? View answer

Asked 3 ´years ago

Question 41

Cutting the cord is okay when replacing the collar cap. Or is there a way to disassemble the plug? View answer

Asked 5 ´years ago

Question 42

My cap is cracked at the area that appears to be "fused" together...I purchased my SJ-30 in May of 2019. How can I get this part? I have looked all over the internet. View answer

Asked 3 ´years ago

Question 43

How do you get the wire through the hole View answer

Asked 3 ´years ago

Question 44

The Flow LED on the panel will turn green for aprox. 10 seconds and then go red for aprox. 2 min. When it will go green again for 10 seconds repeating. Could this be a faulty flow switch or something else? View answer

Asked 3 ´years ago

Question 45

For RJ Series can one replace just the flow control switch while keeping the existing T? Just want to know if we can just replace the switch without replacing the T. View answer

Asked 6 ´years ago

Question 46

I just need the switch and attached cable? View answer

Asked 5 ´years ago

Question 47

Is the connector on the end a standard RJ-11 phone adapter? A critter chewed through mine and I need to patch a new end on. View answer

Asked 4 ´years ago

Question 48

Does this come as show, switch/cable/PVC? View answer

Asked 4 ´years ago

Question 49

Is this the right flow switch for an RJ 60 ? View answer

Asked 4 ´years ago

Question 50

Which direction does the flow switch face. With water flow holding the leg open that already stays open or against the water flow causing the leg to stay down. View answer

Asked 4 ´years ago

Browse by Topic

Tools