Sanitation Q&A
Activity timeframe
when cell is needing replace do you replace the entire unit View answer
Asked 3 ´years ago
Where do you get CO2? View answer
Asked 5 ´years ago | Sanitation > pH Control
How often does the electrolytic cell need to be replaced? View answer
Asked 2 ´years ago
How does direct sunlight for most of the day affect the control unit? View answer
Asked 2 ´years ago
How does this get connected to my pool equipment? View answer
Asked 5 ´years ago
I have a 12,000 G pool, is this too big for me to use? View answer
Asked 5 ´years ago
What is the length of the power cord? View answer
Asked 4 ´years ago
What are the overall dimensions of the unit? View answer
Asked 4 ´years ago
Can we get an adapter kit for a pentair ic 40 View answer
Asked 2 ´years ago
How important to place Core35 after the heater? The heater is about 8 feet from the filter but all the plumbing is underground and the wiring will be a longer distance than desired. This will cause me lots of work on new plumbing. I can easily place it between the filter (pool return) and the heater (which we rarely use in Florida). It this acceptable? View answer
Asked 3 ´years ago
How can I tell what my salinity level is on the Core35 unit? View answer
Asked 3 ´years ago
How long is the power cord? View answer
Asked 3 ´years ago
How can I get a pdf of the manual View answer
Asked 3 ´years ago
We're thinking of replacing out Hayward with this system. Can we reply on the flow switch to turn the chlorinator on and off? The pump is always powered, but has an internal controller as well as variable speed. We can have reduced flow as well as no flow during parts of the day. Will this hurt your system? Thank you in advance. View answer
Asked 2 ´years ago
Does the CircuPool Core 35 come with a sacrificial anode? View answer
Asked 2 ´years ago
i HAVE A 25,000 GAL POOL WILL THE CORE35 BE SUFFICIENT? View answer
Asked 2 ´years ago
Just submitted a question regarding swg and just ran across your Ozone units. Again, 10,000 gallon pool. Light use except for 2-3 weeks when grandkids visit. Which unit would you recommend? I have a Pentair VSP that I run 4-6 hours a day. How long/volume does the 03 unit require? View answer
Asked 2 ´years ago | Sanitation > Ozone Generators
what size pipe is used for the inlet and outlet and is it PVC? View answer
Asked 2 ´years ago
I have a variable speed pump. <!--I run at 2500 rpm for 2 hours, 1000 rpm for 10 hours, and 800 rpm for 12 hours.--> The question is, when I am at the low speed I suspect the flow will not be enough for the flow switch to read so it will not produce salt. Is this correct? Will this harm the system?If I purchase this my plan is to set the pump speeds to get the chlorine level I need. Pool is 15000 gallons View answer
Asked 2 ´years ago
Little add on to previous two questions that I submitted. Pool is located in south Florida (Port Charlotte, FL). Equipment is all outside. Lots of sun, rain and humidity. What would be best configuration for installing swg and O3 units together? Thanks again, Bill View answer
Asked 2 ´years ago | Sanitation > Ozone Generators
Core35 warranty 8 year limited. What is covered? View answer
Asked 2 ´years ago
whats the difference between the core 35 and rj series? View answer
Asked 3 ´years ago
Interested in purchasing this with a variable speed pump and saltwater generator. I understand the saltwater generator can be wired to constant power and will be activated by the flow switch. How do I control the Ozone Generator operation in this setup? View answer
Asked 4 ´years ago | Sanitation > Ozone Generators
What is the minimum GPM flow rate required for the Core series? View answer
Asked 3 ´years ago
can this unit be powered up 24/7, or does it need a timer/clock? View answer
Asked 3 ´years ago
How do I actually use an ozone system on my pool? View answer
Asked 5 ´years ago | Sanitation > Ozone Generators